74
●
Connection of Matrix Switcher (WJ-SX550A)
The matrix switcher is connected to the data port through a
modular cable (furnished with the system controller).
• Setting of AV Codec (transmitter side)
Set the No.3 DIP switch on the transmitter side to the
ON position (cross). Make the following setting for the
[421 SERIAL DATA PORT]
:
Rate: 9 600 or 4 800
Data: 8
Stop bit: 1
Parity: NONE
Parameters of the serial data port should be adjusted,
without fail, between the transmitter and the receiver.
• Setting of the matrix switcher
The setting parameters for the Communication Speed
menu should be adjusted to those for
[421 SERIAL
DATA PORT]
of the AV Codec (transmitter).
Remove a jumper connector from the CN13 on the con-
trol board. (Assume the mode without ENQ.)
SIGUNAL GND
AC IN
JW–AV20
OFF ON
RS–485
RS–232C
ON
↓
6
5
4
3
2
1
1
1
2
2
4
5
3
OUT
IN
TEST
SETUP
REMOTE DATA PORT
HOST PORT
HOST PORT
VIDEO
IN
OUT
TERM
SENSOR IN/TRIGGER OUT
PARALLEL PORT
ISDN
LOCAL
AUDIO
1
2
REMOTE
ON
6
5
4
3
2
1
CONTROL
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
TEST 1
TEST 2
CPU
RS-232C
TIME
ADJUST IN
COM
PRINTER
OUT
IN
VS/VD
VD
OUT
OFF
+9V
+5V
−
5V
POWER
ON
11A00001
OUT
IN
1
OUT
IN
2
OUT
IN
3
OUT
IN
4
MONITOR
ALARM OUT
RESET OUT
OUTPUT
INPUT
1
2
3
4
5
6
7
8
CAMERA IN
VIDEO OUT1
VIDEO OUT2
125V 6A
Matrix Switcher (WJ-SX550A)
AV Codec (transmitter)
It is impossible to connect multiple system controllers in
a daisy chain. Use the ports on the matrix switcher.
Note
●
Connection of Video Multiplexer (WJ-FS616)
• Setting of AV Codec (receiver side)
Set the No.3 DIP switch on the receiver side to the OFF
position and then make the settings in the
[421 SERIAL
DATA PORT]
menu the same as the Matrix Switcher.
Note:
When the WV-CU550A system controller is con-
nected, make the following setting for the
[421 SER-
IAL DATA PORT]
:
Rate: 9 600 or 4 800
Data: 8
Stop bit: 1
Parity: EVEN
• Setting of the system controller (WV-CU350)
Set the MODE switches on the rear of the controller to
the required positions as shown below.
Switch 1 - 3 :
OFF
Switch 4:
ON
Switch 5, 6:
Same Baud Rate as AV Codec.
Baud Rate
Switch 5
Switch 6
4 800bps
ON
OFF
9 600bps
OFF
ON
Switch 7:
ON
Switch 8:
OFF
Caution:
Turn the controller power off after the set-
tings are completed.
• Setting of AV Codec (transmitter side)
Set the No.3 DIP switch on the receiver side to the ON
position and then make the settings in the
[421 SERIAL
DATA PORT]
menu the same as the Matrix Switcher.
Note:
When the WV-CU550A system controller is con-
nected, make the following setting for the
[421 SER-
IAL DATA PORT]
:
Rate: 9 600 or 4 800
Data: 8
Stop bit: 1
Parity: EVEN
• Setting of the video multiplexer
The parameters for the Communication Speed menu
should be set to those for
[421 SERIAL DATA PORT]
of
the AV Codec (transmitter).