49
VQT2Q72
On the unit’s display
Page
F99
≥
The unit fails to operate properly. Press [
Í
/I] on the main unit to switch the unit to
standby for 3 seconds. Now press [
Í
/I] on the main unit again to turn the unit on.
—
HDMI ONLY
≥
Some BD-Video discs can only be output with HDMI.
—
NET
[BTX77]
≥
Displays while VIERA CAST is starting up.
30
No PLAY
≥
There is a viewing restriction on a BD-Video or DVD-Video.
35
No READ
≥
The media is dirty or badly scratched. The unit cannot play.
3
PLEASE WAIT
≥
The unit is carrying out internal process.This is not a malfunction. You cannot operate
the unit while “PLEASE WAIT” is displayed.
≥
When connected to TV (VIERA) with HDAVI Control 4, and power supply is turned off
by the “Intelligent Auto Standby” function on the TV side.
—
27
REMOVE
≥
The USB device is drawing too much power. Remove the USB device.
16
SET
(“
” stands for a number.)
≥
The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
47
UNFORMAT
≥
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an R, +R DL or
DVD-RW (DVD-Video format).
—
UNSUPPORT
≥
You have inserted a media the unit cannot play.
≥
You tried to operate with a non-compatible USB device.
40 – 43
41
U59
≥
The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the
cooling fan on the rear of the unit.
—
U72
U73
≥
The HDMI connection acts unusually.
– The connected equipment is not HDMI compatible.
– Please use HDMI cables that have the HDMI logo (as shown on the cover).
– The HDMI cable is damaged.
—
H
or F
(“
” stands for a number.)
≥
Check and correct the speaker connections.
≥
There is something unusual. (The service number displayed after H and F depends
on the unit’s condition.)
≥
Check the unit using the troubleshooting guide. If the service number does not
disappear, do the following.
1 Disconnect the plug from the household mains socket wait a few seconds, then
reconnect it.
2 Press [
Í
/I] to turn the power on. (The unit may be fixed.)
If the service number does not disappear despite doing the above, request service
from the dealer. Inform the dealer of the service number when requesting service.
8
—
44 – 47
DOCK UNLOCKED
≥
The iPod docking switch lever is not locked in position.
–Make sure that the iPod docking switch lever is properly pushed back into place.
28
IPOD OVER CURRENT ERROR
≥
The iPod is drawing too much power. Remove the iPod, and turn the unit off and on again.
—
START
[BTX77]
≥
The system is being restarted during the firmware update. Please do not turn off power.
30
UPD
/
[BTX77]
≥
The firmware is being updated.
30
FINISH
[BTX77]
≥
The firmware update is complete.
30
NOT CONDITIONAL
≥
The requested operation cannot be conducted.
—
NOT CONNECTED
≥
The iPod is not connected or it is not correctly connected. Reconnect the iPod.
≥
The iPod cannot be operated. Check that there is nothing wrong with the iPod.
28
—
ILLEGAL OPEN
≥
The sliding door is not in the correct position. Turn the main unit off and on again.
—
llllllll
≥
The main unit could not save the modified settings. Some settings may need to be reset.
—
Reference
SC-BTX77&75EGEB-VQT2Q72_eng.book 49 ページ ２０１０年２月１日 月曜日 午前９時３３分
