Panasonic PT-RQ32KU, Руководство по эксплуатации

Страница: 27 / 285

Chapter 1 Preparation — About your projector
ENGLISH - 27
About your projector
Remote control
1
2
6
4
7
5
8
9
10
3
13
12
11
20
14
15
16
23
17
18
19
21
22
Front Top
Bottom
A strap can be attached
depending on the usage.
1 Remote control indicator
Blinks if any button in the remote control is pressed.
2 Power on <
b
> button
Sets the projector to projection mode when the <MAIN
POWER> switch on the projector is set to <ON> and the power
is turned off (standby mode).
3 Power standby <
v
> button
Sets the projector to the state where the projector is turned
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
4 <MENU> button/<ENTER> button/
asqw
buttons
Used to navigate through the menu screen. (
x
page 87)
5 <ON SCREEN> button
Switches the on-screen display function on (display) or off
(hide). (
x
page 82)
6 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed while in automatic adjustment.
(
x
page 83)
7 <ASPECT> button
Switches the aspect ratio of the image. (
x
page 83)
8 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple
projector environment.
9 <STATUS> button
Displays the projector information.
10 <LIGHT> button
Pressing this button lights up the remote control buttons. The
lights will go off when the remote control operation goes idle for
10 seconds.
11 <INPUT MENU> button
Displays the input selection screen. (
x
page 74)
12 Input selection buttons (<DIGITAL LINK>, <DVI-D>, <HDMI>,
<SLOT 1>, <SLOT 2>, <SDI>)
Switches the input signal to project. (
x
page 72)
<DVI-D> button, <HDMI> button, <SLOT 1> button, and
<SLOT 2> button can be used when the optional Interface
Board equipped with corresponding input is installed in the slot
on the projector.
Following buttons are not used with this projector.
<RGB1> button, <RGB2> button, <VIDEO> button, <S-VIDEO
Y/C> button, <DISPLAY PORT> button
13 <SHUTTER> button
Used to temporarily turn off the image. (
x
page 82)
14 <TEST PATTERN> button
Displays the test pattern. (
x
page 84)
15 Lens buttons (<FOCUS>, <ZOOM>, <SHIFT>)
Adjusts the focus, zoom, and lens shift. (
x
page 74)
16 <FUNCTION> button
Assigns a frequently used operation as a shortcut button.
(
x
page 83)
17 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
(
x
page 88)
18 <ID SET> button
Sets the ID number of the remote control in a multiple projector
environment. (
x
page 35)
19 <ID ALL> button
Used to simultaneously control all the projectors with a
single remote control in a multiple projector environment.
(
x
page 35)
20 <LOCK> button
Used to prevent unintended operation by careless pressing of
the buttons and prevent draining the remote control batteries.
Operation of each button on the remote control is disabled by
sliding the <LOCK> button toward the arrow.
21 Remote control signal transmitter
22 Remote control wired terminal
This is a terminal used to connect to the projector via a cable
when the remote control is used as a wired remote control.
(
x
page 36)