Panasonic PT-RCQ10, Руководство по эксплуатации, Страница: 163 / 267

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 163
2) Press the <ENTER> button.
f
The
[FUNCTION BUTTON]
screen is displayed.
3) Press
as
to select a function.
[DISABLE] Disables the <FUNCTION> button.
[SUB MEMORY]
Displays the sub memory list. (
x
page 172)
[SYSTEM SELECTOR]
Switches the [SYSTEM SELECTOR] setting according to the input signal of the image being
projected.
f
When the input signal is anything other than the SDI input
The [PICTURE] menu
→ [SYSTEM SELECTOR] (
x
page 98)
f
When the input signal is the SDI input
The [DISPLAY OPTION] menu
→ [SDI IN] → [SYSTEM SELECTOR] (
x
page 123)
[SYSTEM DAYLIGHT VIEW]
Switches the [SYSTEM DAYLIGHT VIEW] setting. (
x
page 96)
[FREEZE] Freezes the image temporarily. (
x
page 139)
[WAVEFORM MONITOR] Displays the waveform of the input signal. (
x
page 139)
[ASPECT]
Switches the aspect ratio of the image. (
x
page 101)
[PROJECTION METHOD]
Switches the [PROJECTION METHOD] setting. (
x
page 141)
[GEOMETRY] Switches the [GEOMETRY] setting. (
x
page 103)
[OSD POSITION] Switches the [OSD POSITION] setting. (
x
page 133)
4) Press the <ENTER> button.
Note
f
The [FUNCTION BUTTON] screen can also be displayed by holding down the <FUNCTION> button on the remote control.
[STATUS]
Display the status of the projector.
1) Press
as
to select [STATUS].
2) Press the <ENTER> button.
f
The [STATUS] screen is displayed.
3) Press
qw
to switch the pages.
f
The page will change each time you press the button.
[PROJECTOR TYPE] Displays the type of the projector.
[SERIAL NUMBER]
Displays the serial number of the projector.
[PROJECTOR RUNTIME] Displays the runtime of the projector.
[LIGHT RUNTIME] Displays the runtime of the light source 1 and the light source 2.
[CONTINUOUS LIGHTING
TIME]
Displays the elapsed time from when the light source is illuminated.
The elapsed time after the illumination of the light source can be confirmed when adjusting the focus.
The elapsed time is reset when the light source is temporarily turned off such as using the shutter
function.
[MAIN/SUB VERSION] Displays the main and sub versions of the firmware of the projector.
[INTAKE AIR TEMP.]
*1
Displays the status of the intake air temperature of the projector.
[OPTICS MODULE TEMP.]
*1
Displays the status of the internal temperature of the projector.
[EXHAUST AIR TEMP.]
*1
Displays the status of the exhaust air temperature of the projector.
[LIGHT1 TEMP.]
*1
Displays the status of the light source 1 temperature of the projector.
[LIGHT2 TEMP.]
*1
Displays the status of the light source 2 temperature of the projector.
[SELF TEST]
Displays the status of the projector.
[INPUT] Displays the input terminal currently selected.
[SIGNAL NAME] Displays the input signal name.
[MEMORY NO.] Displays the memory number of the input signal.
[BACKUP INPUT STATUS]
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (
x
page 118)
[NUMBER OF REGISTERED
SIGNAL]
Displays the number of registered signals.
[COOLING CONDITION] Displays the set cooling conditions.
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE2 STATUS] Displays the control status of the REMOTE2.