Panasonic CS-MRE7PKE страница 45 Скачать руководство пользователя

Страница: 45 / 110

15.5 Cooling overload control (Cool)

This control detect outdoor pipe temperature and perform the compressor frequency restriction during cooling

operation.

15.6 Heating overload control (Heat)

This control detect indoor pipe temperature and perform the compressor frequency restriction during heating

operation.

This control detect outdoor ambient temperature and perform the fan speed adjustment during heating operation.

15.7 Extreme Low Temperature Compressor low pressure protection control

(Heat)

This control is to prevent low pressure drops too low during extremely low outdoor ambient temperature to

improve the compressor reliability.

During heating operation, when outdoor ambient temperature is in Zone 1, this control will be activated.

Compressor frequency restriction will be based on outdoor piping temperature.

Содержание CS-MRE7PKE















































































































Результаты поиска

Содержание CS-MRE7PKE

Отзывы:

Похожие инструкции для CS-MRE7PKE

Бренды по названию

Популярные бренды

Panasonic CS-MRE7PKE, Руководство по обслуживанию

Результаты поиска

Содержание CS-MRE7PKE

Отзывы:

Похожие инструкции для CS-MRE7PKE

Бренды по названию

Популярные бренды