CQ-C8401U/C8301U/C7401U/C7301U
English
13
12
Preparation
CQ-C8401U/C8301U/C7401U/C7301U
Note:
Adjust the clock when “ADJUST” appears on the
display.
1
Press
[MENU]
to display the menu
display.
For using the remote control, hold down
[SEL]
(MENU)
for 2 sec. or more.
2
Press
[
]
]
or
[
[
]
to display the
DISPLAY menu.
3
Press
[
{
]
to select “CLOCK ADJ”.
4
Press
[BAND]
(
SET
) to confirm the
display.
5
Adjust the setting value.
[
[
]
: Adjusting minutes
[
]
]
: Adjusting hours
[
}
]
: Forward
[
{
]
: Backward
6
Press
[BAND]
(
SET
) to confirm the
adjustment.
7
Press
[MENU]
.
For using the remote control, hold down
[SEL]
(MENU)
for 2 sec. or more.
The demonstration message appears for first use.
1
Set your car's ignition switch to the ACC
or On position.
The demonstration screen appears.
2
Press
[DISP]
(Display).
The demonstration screen is cancelled, and no more
appears.
3
Press
[SRC]
(
PWR
: Power).
Note:
If you would like to turn on the power and make
the demonstration message appear, hold down
[SRC]
(
PWR
: Power)
for 4 sec. or more after turning off the
power in other than the XM mode.
You may need to set the following depending on the
devices to be connected.
Using Subwoofer
¡
Subwoofer level adjustment (
a
page 34)
¡
Subwoofer low pass filter (
a
page 34)
Connecting XM tuner
¡
Connect the optional XM receiver (XMD1000).
¡
To connect the XM receiver (XMD1000), it is required
to use an optional extension cord (XMDPAN100) that is
produced by XM exclusively for Panasonic products.
Getting Started
It is required to sign up to become an XM Satellite Radio
subscriber. After checking your XM Satellite Radio ID,
sign up on the XM’s website or by calling them.
1
Check of XM Satellite Radio ID
¡
Write down the ID indicated on the lower right of your
XM receiver (XMD1000).
¡
Radio ID also can be found by turning your XM Radio
to channel 0. (
a
page 28.)
2
Activate the XM Satellite Radio
Select either of the below to sign up.
¡
Web site: http://www.xmradio.com/activation
¡
Phone number: 1-800-XM-RADIO (1-800-967-2436)
Note:
Refer to the operating instructions for the XM
receiver for details.
The following functions are activated when the Security
Function is ON. (
a
page 35)
¡
The security indicator lights up when removing the
face plate.
¡
The alarm sounds and the message appears on the
screen to warn you to remove the face plate at ACC
off.
Security Indicator
SRC
CQ-C8401U
Preparation
First T
ime Power On
(DEMONSTRATION)
Remote Control Preparation
Security Function
Setting
Other Settings
Clock adjustment
Warning
Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Cautions
¡
Remove and dispose of an old battery immediately.
¡
Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
¡
Follow local regulations when disposing of a battery.
¡
Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Note:
Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under normal use
(at room temperature)
Preparation Before Initial Use
Pull the insulation film out
from the backside of
remote control gently.
Battery Replacement
q
w
q
Remove the battery holder
with the remote control unit
placed on a flat surface.
q
Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
w
Pull it out in the direction
of the arrow using a
tough pointed object.
2
3
w
Put a battery in the case
with (+) side facing up.
e
Put the case back.
Tough pointed object
Back side
Insulation film
