Palmgren 9683408, Руководство по эксплуатации и список запасных частей

Страница: 9 / 40

9
PALMGREN Operating Manual & Parts List 9683408
Anti-kickback pawls:
Kickback is a hazard in which the workpiece is thrown back toward
the operator. The teeth on the anti-kickback pawls point away from
the workpiece. If the workpiece should be pulled back toward the
operator, the teeth dig into the wood to help prevent or reduce the
possibility of kickback.
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Description
Out-feed support
Riving knife
Blade guard
Sub fence
Table insert
Rip fence locking handle
Bevel scale
Height/bevel adjusting handwheel
Bevel locking lever
Stand leg locking knob
Stand extension pole
Saw blade
Anti-kickback pawls
Work table
Mitre gauge groove
Plug cable storage
Blade guard storage
Plug cable
Dust extraction port
Blade guard storage
Anti-kickback pawls storage
Rubber levelling pad
Roller wheel
Mitre gauge storage
Sub fence storage
Right extension table
Rip fence
Height-adjusting knob
Overload reset switch
Foldable stand
On/Off switch
Stand handle
Push stick
Blade wrench
Front rail
Mitre gauge
Bevel scale and bevel indicator:
The easy-to-read scale and indicator on the front of the cabinet
shows the exact blade angle.
Saw blade:
For maximum performance, it is recommended that you use the
40-tooth, 10" (25.4 cm) carbide-tipped combination blade provided
with your saw. The blade is raised and lowered with the
height/bevel adjusting handwheel. Bevel angles are locked with
the bevel locking lever.
WARNING!
• Use only 10" (25.4 cm) diameter blades rated at maximum safe
operating speeds of 4500 RPM or higher. Failure to heed this
warning could result in personal injury.
• The blades should always be kept sharp. Use a reputable
sharpening service to sharpen the blades when needed.
• Never store the blades stacked on top of one another. Place
material such as cardboard between them to keep the blades
from coming into contact with one another.
Blade guard:
The guard is installed over the riving knife. It protects the
operator’s hand from being cut while providing a clear view of the
material to be cut during throughsawing cuts.
Bevel locking lever:
This lever, under the work table surface on the front of the cabinet,
locks the angle setting of the blade.
Height/bevel adjusting handwheel:
Located on the front of the cabinet, this handwheel is used to
lower and raise the blade for adjustments or blade replacement.
The handwheel also makes the adjustment for bevel angles easy.
Rip fence locking handle:
The handle on the front of the rip fence releases or locks the rip
fence with respect to the work table.
Mitre gauge:
This mitre gauge aligns the wood for a cross cut. The easy-to-read
indicator shows the exact angle for a mitre cut.
Mitre gauge grooves:
The mitre gauge rides in these grooves on either side of the blade.
Front rail:
Front rail provides support for the rip fence.
Rip fence:
The rip fence is a sturdy metal fence that can be locked to the work
table to guide the workpiece securely.
Scale:
Located on the front rail, the easy-to-read scale provides precise
measurements for rip cuts.
Riving knife:
The riving knife is a metal piece, slightly thinner than the saw
blade, used to keep the kerf open to prevent kickback.
Arbour:
The arbour is a shaft on which a blade is mounted.
Work table:
The surface to which the workpiece is attached while cutting.
Overload protection:
The saw is equipped with an overload reset switch to prevent the
saw from overload damage. The saw will automatically shut off if
the machine experiences overloaded cutting or low voltage. Wait
for the motor to cool down for at least five minutes. Press the
overload reset switch button to reset the overload switch. After the
motor has cooled down, press the green “I”-button on the ON/OFF
switch to restart saw.
Out-feed support:
The out-feed support is provided at the rear end of the work table.
26
25
24
23
27
22
19 20 21
15
16
17
18
13 14 12