Pall PadMixer 1000 Premium Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 48

background image

020-17467-00 Instructions For Use PadMixer 1000 Premium RevD

17

Figure 20: Screen to change additional Factory settings

4.3.4. Inflate

This function is used to inflate the mixing biocontainer with compressed air or nitrogen.
When activated the icon turns green and the compressed air valve is activated.

The compressed air remains active until one of the following points:



The function is cancelled by touching the INFLATE icon on the touch screen again



The mixing biocontainer is inflated to the point that it presses against the mixing

biocontainer detection. However, if the mixing biocontainer is emptied and the
detection is released the compressed air will reactivate after a delay of three
seconds



The emergency stop is pressed



The protective front cover is opened.

4.3.5. Print

This prints out the data for the last finished recipe. To print the last recipe, make sure the
mixing system has completely stopped rotating.

Note: the total mixing time stated on the label may be a few seconds shorter than the
difference between  the start and finish times. The reason is that the last deceleration time is
not included in the calculation of  the  total  mixing  time,  but  the  finish  time  is  not
determined  until  the  mixer  has  come  to  a  complete  standstill.

4.3.6. Reset

This resets all error messages, for example after using the emergency stop.

«
...
15
16
17
18
19
...
»

Содержание PadMixer 1000 Premium

















































Отзывы:

Нет отзывов

Похожие инструкции для PadMixer 1000 Premium

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: ACDC Страницы: 4

Бренд: Kawai Страницы: 10

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренд: V-TEK Страницы: 112

Бренд: Idmed Страницы: 2

Бренд: Jacobsen Страницы: 16

Бренд: Jacobsen Страницы: 20

Бренд: Jacobsen Страницы: 100

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Avisa Line XL04

Бренд: FHF Страницы: 2

Бренд: Joerns Healthcare Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды