paladin HARLEY POWER BOX RAKE T6 Скачать руководство пользователя

Страница: 9 / 50

MODEL T6

HARLEY POWER BOX RAKE®

movements are correct.

Make sure all hydraulic hoses, fittings, and valves are in good condition

and not leaking before starting power unit. Check and route hoses care-

fully to prevent damage.

Hoses must not be twisted, bent sharply, kinked, frayed, pinched, or come

into contact with any moving parts.

Operate moveable components through full operational range to check

clearances. Replace damaged hoses immediately.

Ensure implement is properly attached, adjusted, and in good condition.

Tractor must be equipped with ROPS and seat belt/operator restraint.

Keep seat belt/operator restraint securely fastened/engaged. Falling off

tractor can result in death from being run over or crushed. Keep ROPS

systems in place at all times.

SAFELY OPERATE EQUIPMENT

Improper operation can cause the machine to tip or roll over and cause injury

or death.

Keep tractor lift arms and attachment as low as possible.

Turn on level ground.

Go up and down slopes, not across them.

Keep the heavy end of the machine uphill.

Only engage power when equipment is at ground level. Always disengage

power when equipment is raised off the ground.

Do not disconnect hydraulic lines until all system pressure is relieved.

Never go underneath equipment lowered to the ground or raised.

Hydraulic system leak down, hydraulic system failures, mechanical failures

or movement of control levers can cause equipment to drop or rotate

unexpectedly and cause severe injury or death.

Never direct discharge toward people, animals, or property.

Do not operate equipment while under the influence of alcohol or drugs.

Operate only in the daylight or good artificial lighting.

Always comply with all state and local lighting and marking requirements.

Ensure equipment is properly attached, adjusted and in good operating

condition.

Before starting tractor, check all equipment driveline guards for damage

and make sure they rotate freely on all drivelines. Replace any damaged

guards. If guards do not rotate freely on drivelines, repair and replace

bearings before operating.

Make sure driveline is correct length to prevent bottoming out or pulling

apart during the full lift range of the hitch.

Make sure spring-activated locking pin or collar slides freely and is seated

firmly in tractor PTO splined groove.

A minimum 20% of tractor and equipment weight must be on tractor front

wheels with attachments in “transport” position. Without this weight, tractor

could tip over causing personal injury or death. The weight may be at-

tained with a loader, front wheel weights, ballast in tires, or front tractor

weights. When attaining wheels, you must not exceed the Roll Over Pro-

tection Structure (ROPS) weight certification. Weigh the tractor and equip-

ment. Do not estimate.

WARNING

Содержание HARLEY POWER BOX RAKE T6



















































Результаты поиска

Содержание HARLEY POWER BOX RAKE T6

Отзывы:

Похожие инструкции для HARLEY POWER BOX RAKE T6

Бренды по названию

Популярные бренды

paladin HARLEY POWER BOX RAKE T6, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание HARLEY POWER BOX RAKE T6

Отзывы:

Похожие инструкции для HARLEY POWER BOX RAKE T6

Бренды по названию

Популярные бренды