manualshive.com logo in svg

paladin HARLEY POWER BOX RAKE T6, Руководство оператора и каталог запасных частей

Поделиться
Скачать
paladin HARLEY POWER BOX RAKE T6 Скачать руководство пользователя страница 14

MODEL T6 

HARLEY POWER BOX RAKE®   

3

OPERATIONAL PROCEDURE

POWER RAKE FUNCTION

The tractor PTO drives the roller, which digs into the ground, cultivating and pulling up rocks, 

roots, and debris.  The clean soil goes between the roller and barrier while the rocks, roots, 

and debris work to the side in a windrow.

With the endplates mounted in the working position and the rake straight (endplates parallel 

with tractor tires), material can be moved along, filling in the low spots.

Maximum safe PTO operating speed is 540 rpm.

Before using your new Harley Power Box Rake, the slip clutch assembly must be in RUN-IN.  

See CLUTCH in the maintenance section, page 20, for the RUN-IN procedure.  After you have 

completed the RUN-IN of the clutch, return to the operating instructions and proceed with start-

up.  Failure to run the clutch in could result in pre-mature drive line failure and warranty will be 

voided.

Start tractor engine.

Lower power rake slowly to the ground.

Engage tractor PTO.

Increase engine rpm to give desired rpm at the roller.  Normal operating speed must not ex-

ceed 540 rpm.  If operating in heavy rock, reduce the speed slightly.

Move the tractor forward.  Select a slow tractor speed and increase slightly until operation is 

satisfactory.

Ground Speed

Ground speed should be between 3 and 5 mph under normal conditions.  In heavy rock, reduce 

the ground speed to  to 3 mph.

Power Rake Angle Adjustment

The power rake may be angled up to 5 degrees left or right for placing material in a windrow.  

With the power rake angle cylinder connected to a tractor hydraulic control valve, move tractor 

control valve to select the desired angle.  Return the tractor control to neutral to maintain the 

selected angle.

Power Roller

The roller should be level with the ground.  To level rake from side to side, adjust one of the tractor 

3-point lower lift arms.

The power rake should be level front to back.  Level the rake using the tractor 3-point top link, 

the 3-point lift arms, or the gauge wheels.

Содержание HARLEY POWER BOX RAKE T6



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды