OWL WT-1 Скачать руководство пользователя страница 54

Страница: 54 / 56

Repair.

Repair of this unit by unauthorized personnel is prohibited, and will void any warranty associated with the unit.

Cleaning.

For accurate readings, the optical connectors on the WaveTester and the connectors on the patch cords should be

cleaned prior to attaching them to each other. Minimize dust and dirt buildup by replacing the dust caps after each use.

Calibration.

It is recommended to have Optical Wavelength Laboratories calibrate this unit once per year.

Warranty.

The WaveTester comes standard with a two-year factory warranty, which covers manufacturer defect and

workmanship only.

APPENDICES

SPECIFICATIONS

MAINTENANCE AND CALIBRATION INFORMATION

CONTACT INFORMATION

Address:

Phone:

Internet:

Optical Wavelength Laboratories, Inc.

262-473-0643

OWL-INC.COM

N9623 US Hwy 12
Whitewater, WI 53190

Visual Fault Locator Port Upgrade

The WaveTester optical power meter may be upgraded to include an optional visual fault locator (VFL), useful for locating bends,
breaks, and other anomalies in the near-end splice tray, as well as visual fiber identification up to 5km away!

Upgrading to a VFL port requires the charger port to be removed from the unit.

OPTIONAL UPGRADE INFORMATION

1: Bold wavelengths are NIST Traceable
Conforms to the Harmonized European Standards EN 61326-1 and EN 61010-1.

WAVETESTER OPTICAL POWER METER (WT-1)

InGaAs

850

1300

1310

, 1490,

1550

+5 to -60 dBm

±0.20 dB

0.01 dB

Up to 1000 hours (Re-chargeable Lithium Polymer)

2.5mm/1.25mm universal

dBm, dB, mW, µW
up to 200 readings

Backlit LCD

Yes

-10 to 55° C
-30 to 70° C

2.75 x 4.94 x 1.28 inches (69.85 x 125.48 x 32.51 mm)

10 oz. (284g)

Detector Type

Calibrated Wavelengths

Measurement Range

Accuracy

Display Resolution

Battery Life

Connector Type

Measurement Units

Data Storage

Display Type

Auto-shutdown

Operating Temperature

Storage Temperature

Dimensions

Weight

KEY SPECIFICATIONS

Содержание WT-1

























































Результаты поиска

Содержание WT-1

Отзывы:

Похожие инструкции для WT-1

Бренды по названию

Популярные бренды

OWL WT-1, Руководство по эксплуатации

Результаты поиска

Содержание WT-1

Отзывы:

Похожие инструкции для WT-1

Бренды по названию

Популярные бренды