OWL WT-1 Скачать руководство пользователя страница 16

Страница: 16 / 56

Verify Proper Operation of the Equipment, cont.

Connect the power meter and light source together with the mandrel-wrapped patch cable as shown in Figure 4 below.

Compare the reading on the WaveTester to Table 2 for acceptable power levels. The patch cable should be replaced if it
is below the acceptable power level.

Once proper operation has been verified, continue on to the next step.

Set Reference

Setting a reference is commonly referred to as “zeroing”.

With the power meter and light source still connected as shown in Figure 4, press and hold

on the WaveTester to set

the reference for 850nm.

The WaveTester display should change to show readings in ‘dB’, and the power reading should be approximately 0.00

dB. This means that the meter and light source have been successfully “zeroed” at 850nm.

If testing at 1300nm is also required, connect a mandrel-wrapped patch cable to the 1300nm port, then

UNITS

ZERO

QUICK REFERENCE GUIDES

Optical Power Meter:

WAVETESTER

Fiber Optic Light Source:

DUAL OWL Series Multimode Sources

PAGE 3 OF 5

FIGURE 4

Set

Optical

Reference

SC connectors shown here;
connector style may vary

LIGHT SOURCE

CONNECTOR PORTS

Do NOT insert angled physical
contact (APC) connectors

dBm

20.00

850

62.5/125 µM

50/125 µM

Replace at

-21.00 dBm
-24.00 dBm

-19.0 to -21.0 dBm
-22.0 to -24.0 dBm

TABLE 2

Core Size

Acceptable Power Level

Содержание WT-1

























































Результаты поиска

Содержание WT-1

Отзывы:

Похожие инструкции для WT-1

Бренды по названию

Популярные бренды

OWL WT-1, Руководство по эксплуатации

Результаты поиска

Содержание WT-1

Отзывы:

Похожие инструкции для WT-1

Бренды по названию

Популярные бренды