OWL WT-1 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 56

background image

Required Accessories

(3) one-meter patch cables – (ensure proper connector type and fiber type)
(2) fiber optic adapters/couplers – (ensure proper connector type)

Patch Cable Insertion Loss

Patch cables should be tested periodically to ensure that they are okay to use for
testing. Use the following procedure to test both multimode and singlemode
patch cables.

If testing at more than one wavelength, this procedure must
be performed for each wavelength separately.

Connect the WaveTester to a fiber optic light source using the 3-jumper
reference method as shown at right. Power on the light source according
to manufacturer instructions.

Press

to power on the WaveTester optical power meter, if necessary.

Press

until the wavelength on the WaveTester matches the output

wavelength of the light source.

Press and hold

for approximately 2 seconds to set the reference.

The WaveTester will change to show loss in ‘dB’, and the loss value
should be very close to 0.00 dB.

Setting a reference is commonly referred to as “zeroing”.

Remove the center cable as shown at right.

Insert a patch cable under test between the two fiber optic
adapters/couplers, then record the loss value in ‘dB’.

Repeat steps

and

for each patch cable being tested.

AUTO

UNITS

ZERO

7

TEST PROCEDURES

3-jumper Reference
Method Setup

PATCH CABLE TESTING

Insertion Loss Test

«
...
7
8
9
10
11
...
»

Содержание WT-1

























































Отзывы:

Нет отзывов

Похожие инструкции для WT-1

Бренд: A&D Страницы: 102

Vigilant ELM Series

Бренд: Eagle Eye Power Solutions Страницы: 9

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 12

Бренд: PAT Страницы: 57

Бренд: R&S Страницы: 733

Бренд: R&S Страницы: 369

Бренд: X-Rite Страницы: 45

Бренд: X-Rite Страницы: 22

Бренд: X-Rite Страницы: 50

Бренд: bentrup Страницы: 9

Бренд: Mic Страницы: 2

Бренд: Hanna Instruments Страницы: 28

Trimble Ranger 3

Бренд: Badger Meter Страницы: 20

Бренд: A&D Страницы: 38

CVM-MINI-Ethernet Series

Бренд: Circutor Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды