Ormazabal ekor.rpa Series Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 116

background image

IG-267-EN versión 01; 07/04/2017

102

Communications

General Instructions

ekor

.rpa

12. Communications

12.1. Physical medium: RS-485

The physical medium used to establish telecontrol
communications for the

ekor

.rpa-100 series is a twisted pair

cable which connects to the rear RS-485 port (identified as
COM0 and COM1) through an RJ-45 connector.

8

Not used

7

Not used

6

GND

5

485 (-)

4

485 (+)

3

Not used

2

Not used

1

Not used

8

Not used

7

Not used

6

GND

5

485 (-) 485 (1)

4

485 (+)

3

GND

2

485 (-) 485 (2)

1

485 (+)

Figure 12.1.

RS-485

The COM0 is the port used when the unit works as a
telecontrol slave (MODBUS or PROCOME slave).

The communication parameters for the RS-485 COM0 port
can be modified using the user settings. These settings are
classified in the field “

Communications/COM_485

” and are as

follows:

•

Peripheral number

: To set the slave number (from 1 to 99).

•

Bauds

: Transmission speed (1200, 2400, 4800, 9600,

19200 or 38400 bauds).

•

Parity

: Parity (No, Even or Odd).

•

Length

: Length (7 or 8 bits)

•

Stop bits

: Stop bits (1 or 2 bits)

•

Protocol

: Protocol which speaks through report 485

(Cirbus, MODBUS or PROCOME).

The COM1 port is the port used when the unit works as a
MODBUS master for the temperature sensors connected to
the bus. This connection may be carried out in either of the
2 RS-485 ports (can be chosen by configuration) available
in the COM1.

Temperature supervision through the temperature sensors
will only be functional as an option in the

ekor

.rpa-120

models, meaning the COM1 will only apply for these models.

12.1.1. MODBUS protocol

The

ekor

.rpa-100 unit can be configured for the COM0

port communication protocol to be MODBUS. The system
therefore works as a MODBUS slave in RTU transmission
mode (Binary).

The main advantage of this mode over the ASCII mode is
that the information is packed tighter, allowing a higher
data transmission rate at the same communication speed.
Each message is transmitted as a continuous string, as
silences are used to detect the end of the message. The
minimum duration of the SILENCE is 3.5 characters.

RTU message frame

Start

Address

Function

Data

CRC

End

Silence

8 bits

8 bits

n x 8 bits

16 bits

Silence

Table 12.1.

RTU message frame

The MODBUS ADDRESS of the relay (also called peripheral
number) is a byte that takes values between 0 and 99.

The master addresses the slave, indicating its address in the
respective field, and the slave answers by indicating its own
address. The "0" address is reserved for the broadcast mode
so it can be recognised by all slaves.

«
...
100
101
102
103
104
...
»

Содержание ekor.rpa Series





















































































































Отзывы:

Нет отзывов

Похожие инструкции для ekor.rpa Series

Бренд: Zander Aachen Страницы: 10

Бренд: Eaton Страницы: 3

UPLC CU44-VER04

Бренд: Ametek Страницы: 129

Бренд: Eaton Страницы: 72

Бренд: SafeTrust Страницы: 11

Бренд: NatComm Страницы: 16

Бренд: Malmbergs Страницы: 2

Бренд: Danfoss Страницы: 76

Бренд: CARLO GAVAZZI Страницы: 6

Бренд: Allen-Bradley Страницы: 2

Бренд: HANYOUNGNUX Страницы: 2

Бренд: GE Multilin Страницы: 338

Бренд: jablotron Страницы: 2

LUXOMAT ROUTER2-DALI-SYS-REG

Бренд: B.E.G. Страницы: 4

High PROTEC MRU4

Бренд: Woodward Страницы: 655

Бренд: SOUNDLIGHT Страницы: 8

Бренд: SOUNDLIGHT Страницы: 10

Бренд: Plejd Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды