Ormazabal ekor.rpa Series Скачать руководство пользователя страница 47

Страница: 47 / 116

IG-267-EN versión 01; 07/04/2017

General Instructions

ekor

.rpa

Detection, automation and control functions

5.3.3. Switch control statuses

The switch control unit implemented in the

ekor

.rpa-100

system generates a series of signals which report its status.
These signallings are:

•

Switch status

: Indicates the current status of the switch:

open or closed.

•

Opening correct by protection trip

: Indicates that

the switch opening caused by protection tripping or
external tripping was correct.

•

Opening failure by protection trip

: Indicates that there

was an error in the switch opening caused by protection
tripping or external tripping.

•

Opening correct by remote opening command

Indicates that the switch opening caused by a remote
control order was correct.

•

Opening failure by remote opening command:

Indicates that there was an error in the switch opening
caused by a remote control order.

•

Correct closing by reclosing

: Indicates that the switch

closing caused by a reclosing order was correct.

•

Closing failure by reclosing

: Indicates that there was

an error in the switch closing caused by a closing order.

•

Correct closing by remote closing command

: Indicates

that the switch closing caused by a remote control order
was correct.

•

Closing failure by remote closing command

: Indicates

that there was an error in the switch closing caused by a
remote control order.

5.4. Remote control

The

ekor

.rpa-100 units are fitted with a serial

communication port which can be used for telecontrol,
following standard RS-485,

allowing connection of up to

a maximum of 32 units in a single bus

. The 485 port has

a twisted pair connection. The Distribution or Transformer
Substation telecontrol terminal sends the encoded frames
for each of the

ekor

.rpa-100 units they are connected

to via the RS-485 bus. The communication between the
communications terminal and the dispatching centre
depends on the protocol used.

Some of the functions available through remote control are:

•  Switch status display.
•  Earthing switch display.
•  Switch operation.
•  Switch error monitoring.

• Coil monitoring.
• Phase and neutral current metering with module and

angle relative to VA.

• Phase and neutral voltage metering with module and

angle relative to VA.

•  Active, reactive and apparent power metering.
•  Energy metering.
•  Display presence/absence of voltage in each phase A, B

and C.

•  Display and set system parameters.
•  Fault reports record.
•  Event record.
•  Time synchronisation.
•  Error/alarm indications.

Содержание ekor.rpa Series





















































































































Результаты поиска

Содержание ekor.rpa Series

Отзывы:

Похожие инструкции для ekor.rpa Series

Бренды по названию

Популярные бренды

Ormazabal ekor.rpa Series, Общее руководство по инструкции

Результаты поиска

Содержание ekor.rpa Series

Отзывы:

Похожие инструкции для ekor.rpa Series

Бренды по названию

Популярные бренды