Ormazabal ekor.rpa Series Скачать руководство пользователя страница 89

Страница: 89 / 116

IG-267-EN versión 01; 07/04/2017

General Instructions

ekor

.rpa

User interface

Configuration

This tab is used to configure the different parameters of the
substation: Protection unit settings, remote IP addresses…

•

Protection

: Display and change protection unit settings.

Figure 11.12.

Configuration

•

IP RTU

: Display and change IP parameters, NTP

parameters, LDAP parameters, timings, etc. They can be
loaded and downloaded in an .xml file.

Figure 11.13.

Display and change RTU parameters

•

Password

: Used to change the passwords for

administrator mode and display mode (when not
managed by LDAP).

Figure 11.14.

Change administrator mode and display mode passwords

•

Special automation menus

: Used to change the

configuration parameters of the different automations
implemented.

Figure 11.15.

Menus screen

Содержание ekor.rpa Series





















































































































Результаты поиска

Содержание ekor.rpa Series

Отзывы:

Похожие инструкции для ekor.rpa Series

Бренды по названию

Популярные бренды

Ormazabal ekor.rpa Series, Общее руководство по инструкции

Результаты поиска

Содержание ekor.rpa Series

Отзывы:

Похожие инструкции для ekor.rpa Series

Бренды по названию

Популярные бренды