background image

27

Regulations and standards

12 Regulations and standards

This product is recognized by UL under the UL and CSA standards, and also affixed the CE Marking under the Low 
Voltage Directive and the EMC Directive.

12.1  UL Standards, CSA Standards

Applicable Standards

Certification body

Standards File No.

UL 61800-5-1 
CSA C22.2 No.274

UL

E171462

12.2  CE Marking

„

„

Low Voltage Directive

 

This product is designed and manufactured to be incorporated in equipment.

 

This product cannot be used in IT power distribution systems.

 

Install the product inside an enclosure in order to avoid contact with hands.

 

When installing the motor and driver, securely connect their Protective Earth Terminals.

 

Isolate the motor cable, power supply cable and other drive cables from the encoder cable and signal cables (CN5 to 
CN7) by means of double insulation.

Applicable Standards

Installation conditions (EN Standards)

EN 61800-5-1

 

To be incorporated in equipment.

 

Overvoltage category:

 

Pollution degree: 2

 

Protection against electric shock: Class

„

„

EMC Directive

This product has received EMC compliance under the conditions specified in "Example of installation and wiring" on the 
USER MANUAL. The final level of conformance of your mechanical equipment to the EMC Directive will vary depending 
on such factors as the control system equipment used with the motor and driver, configuration of electrical parts, 
wiring, layout, and hazard level. It therefore must be verified through conducting EMC measures on your mechanical 
equipment.

Applicable standards

EMI

EN 55011 Group 1 Class A 
EN 61000-6-4, EN 61800-3

EMS EN 61000-6-2, EN 61800-3

Caution: This equipment is not intended for use in residential environments nor for use on a low-voltage public network 

supplied in residential premises, and it may not provide adequate protection to radio reception interference in 
such environments.

12.3  Republic of Korea, Radio Waves Act

KC Mark is affixed to this product under the Radio Waves Act, the republic of Korea.

12.4  RoHS Directive

The products do not contain the substances exceeding the restriction values of RoHS Directive (2011/65/EU).

Содержание BX2 Driver Edition Series





























Отзывы: