Opengear IP-KVM 1001 Скачать руководство пользователя страница 8

Страница: 8 / 109

KVM over IP User Manual

Page 8 of 109

Installation and Start Up

Introduction

This chapter overviews the general installation and configuration of your IP-KVM and steps through

in detail the physical installation and connection to controlled devices

2.1

General installation and configuration steps

Step 1

Check kit contents (refer

Chapter 2.2

)

Step 2

IP-KVM installation and connection to the target server and network (refer

Chapter

2.5 - 2.7

)

Step 3

Configure the IP-KVM network settings (refer

Chapter 3.1 - 3.3

)

Step 4

Configuring the KVM settings for the Target Server and IP-KVM (refer

Chapter 3.4)

2.2

Package checklist

The IP-KVM package consists of the followings items:

The IP-KVM unit

CD-ROM (software utilities and user manual)

Quick Start Guide

DC power supply adapter

3-in-1 Integrated Adapting Local Cable

USB A-mini cable

Serial cable (RJ45 to DB9F)

Rack mounting kit (with brackets and screws)

Footpads set

2.3

Product Views

The IP-KVM has an attached 3-in-1 Integrated Host Cable to simplify cable connection. Similarly the

dual LAN ports provides flexibility of cascaded wiring and the palm size form factor enables flexible

installation.

Содержание IP-KVM 1001














































































































Результаты поиска

Содержание IP-KVM 1001

Отзывы:

Opengear IP-KVM 1001, Руководство пользователя, Страница: 8 / 109

Результаты поиска

Содержание IP-KVM 1001

Отзывы: