Opengear IP-KVM 1001 Скачать руководство пользователя страница 24

Страница: 24 / 109

KVM over IP User Manual

Page 24 of 109

Click

Apply

Note:

To configure using the web browser, the Remote Console computer must have an IP address in the

same network range as the IP-KVM (i.e.it must have an address 192.168.0.0 - 192.168.0.255). If
setting up the Remote Console computer in this range is not convenient you can as an alternate set
the IP-KVM IP address using the

psetup

program or using a serial console

3.3

Initial IP configuration using the serial console

The IP-KVM has a serial line interface (host side) which can be accessed using a serial terminal (or

terminal emulator). This connector is compliant with the RS-232 serial line standard and is

configured as shown below:

Parameter

Value

Bits/second

115200

Data bits

Parity

Stop bits

Flow Control

None

When configuring the IP with a serial terminal (such as Hyper Terminal):

Reset the IP-KVM and immediately press the

ESC

key. You will see some device information,

and a

prompt

Enter

config

then press

Enter

key and wait for a few seconds for the configuration

questions to appear

As you proceed the following questions will appear on the screen. To accept the default

values shown in square brackets below, press

Enter

key:

Содержание IP-KVM 1001














































































































Результаты поиска

Содержание IP-KVM 1001

Отзывы:

Opengear IP-KVM 1001, Руководство пользователя, Страница: 24 / 109

Результаты поиска

Содержание IP-KVM 1001

Отзывы: