Opengear IP-KVM 1001 Скачать руководство пользователя страница 63

Страница: 63 / 109

KVM over IP User Manual

Page 63 of 109

The drive redirection software tries to lock the local drive before it is redirected. That

means that it tries to prevent the local operating system from accessing the drive as long as

it is redirected. This may also fail, especially if a file on the drive is currently open. In the

case of a locking failure, you will be prompted if you want to establish the connection

anyhow. This should not be a serious problem when the note above is respected. If the

write support is enabled, a drive which is not locked might be damaged by the Drive

Redirection.

Clicking on the

Disconnect

button will disconnect the Drive Redirection connection.

Note:

Virtual Drive creation is by Device manner not by Partition. Which means it looks for I/O in BIOS and

sends the corresponding signal to host computer. This way, you are sending the entire hard drive (may

consist of ‘X’ numbers of partitions) and emulate whatever number of partitions on host computer. You may

also emulate a DVD-Drive with the same procedure. However, this DVD-Drive

Does NOT

support Bootable

function like Floppy and CD-ROM emulation.

Содержание IP-KVM 1001














































































































Результаты поиска

Содержание IP-KVM 1001

Отзывы:

Opengear IP-KVM 1001, Руководство пользователя, Страница: 63 / 109

Результаты поиска

Содержание IP-KVM 1001

Отзывы: