Omron K3TS Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 97

background image

!&

Communications Unit Number

The communications unit number is an identification number by which the
host computer to which the Intelligent Signal Processor is connected identi-
fies the Intelligent Signal Processor. The Thumbwheel Switches Models are
not provided with the communications output function; therefore, communica-
tions unit number setting is not required. For details, refer to the K3TS Com-
munication Operation Manual.

In order to set the communications unit number, follow the instructions out-
lined on the flow diagram (after the table) and set within the following range:

Setting range

to

RUN mode

Press and hold the Level Key for 2 seconds to select level 1.

Setting level 1

Setting level 2

Press and hold the Level Key and Up Key simultaneously for
1 second to select level 2.

Press the Display Key.

LED Models

Press and hold the Level Key for
1 second to return to RUN mode.

Press and hold the Level Key for
1 second to return to level 1.

Press the Shift Key several times to display

.

Use the Up Key and Shift Key to set the unit number. Press the Display
Key to write the value.

! $

Section 6-2

«
...
49
50
51
52
53
...
»

Содержание K3TS


































































































Отзывы:

Нет отзывов

Похожие инструкции для K3TS

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

ROADRECORDER 8000

Бренд: Safety Vision Страницы: 40

Бренд: National Instruments Страницы: 8

Бренд: QNAP Страницы: 54

Бренд: ICOP Technology Страницы: 34

Бренд: Kontron Страницы: 62

Open Standard Module RPX30 EVA-MI V1

Бренд: iesy Страницы: 9

Бренд: ICS ELECTRONICS Страницы: 4

LITTLE BOARD P5X

Бренд: Ampro Corporation Страницы: 121

Бренд: Planet Страницы: 20

Airborne M2M ABDN-er-DP55 Series

Бренд: B+B SmartWorx Страницы: 120

Бренд: DigiTech Страницы: 28

ENHANCED PSD 239 H2R

Бренд: ADTRAN Страницы: 2

Бренд: Allen-Bradley Страницы: 76

Бренд: Z3 Technology Страницы: 83

Бренд: M86 Security Страницы: 512

Бренд: CAME Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды