Omnia Omnia-6EX Скачать руководство пользователя страница 7

Страница: 7 / 125

Omnia-6ex Use and Operation Manual – V: 1.20

Omnia 6 Performance Specifications

As of October 2003 – Version 7.0.0 Software

Note: All measurements made with the supplied “FACT TEST2” preset, which is available in the Preset
Menu.

System

Signal to Noise:

The measured noise floor will depend upon the settings of the Input and

Output Gain controls. The Omnia 6's noise floor is primarily governed by

the dynamic range of the 24-bit Crystal Semiconductor CS5360 A/D Converter,

which has a specified Dynamic Range of 105 dB. The dynamic range of

the Omnia 6 digital signal processing chain is 144 dB. Typical SNR using

the “FactTest2” preset is greater than –80dB referenced to 100%

modulation.

Distortion:

No greater than 0.01% THD 20 Hz -- 20 kHz bandwidth.

Conventional FM Specifications (FM Analog)

Frequency Response:

Complies with the standard 50 or 75 microsecond pre-emphasis curve

within ± 0.50 dB, 30 Hz to 15 kHz. The analog left/right outputs and

AES/EBU Digital outputs can be configured for flat or pre-emphasized

output.

Signal-to-Noise Ratio:

> -80 dB de-emphasized, 20 Hz –- 15 kHz bandwidth, referenced to

100%

modulation).

System Distortion:

Less than 0.01% THD, 20 Hz – 7.5 kHz. Second harmonic distortion

above 7.5 kHz is not audible in the FM system

Stereo Separation:

Greater than 65 dB, 20 Hz –- 15 kHz; 70 dB typical.

Crosstalk:

> -70 dB, 20 Hz -- 15 kHz.

Composite Outputs:

Configuration: Two electrically independent outputs. Software based

level

adjustment.

Source Impedance: 10 ohms or 75 ohms, jumper-selectable. Single-ended

and floating over chassis ground.
Load Impedance: 50 ohms or greater load is suggested.
Output

Level

Ranges:

Low Range: 0.66 to 5.02 V P-P, High Range: 1.45 to 11.02 V P-P,
software selectable.

Pilot Level: Adjustable from 6.0% to 12.0% in 0.1% steps.

Pilot Stability: 19 kHz, ± 0.5 Hz.

D/A Conversion: Burr Brown PCM1704, 24-bit sign-magnitude D/A

converter.

Signal-to-Noise

Ratio:

-85

typical, 75 µS de-emphasized, 15 kHz

bandwidth, referenced to 100% modulation).

Distortion: < 0.02% THD 20 Hz – 15 kHz bandwidth, 75 µS de-

emphasized,

referenced

100%

modulation.

Содержание Omnia-6EX






























































































































Результаты поиска

Содержание Omnia-6EX

Отзывы:

Бренды по названию

Популярные бренды

Omnia Omnia-6EX, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Omnia-6EX

Отзывы:

Бренды по названию

Популярные бренды