Omnia Omnia-6EX Скачать руководство пользователя страница 28

Страница: 28 / 125

Omnia-6ex Use and Operation Manual – V: 1.20

Remote Control Session via Network Indicator

An exclamation mark inside a yellow

triangle will show up in the lower left

corner of the Main Menu screen when a

Network remote session is in progress.

A remotely connected network session

has priority over local control of the

front panel, so during a Network remote

session the Main Menu will be grayed

out. You may disconnect a Network

remote session and regain front panel

control by clicking the Disconnect

remote button.

Omnia 6 Main Menu

The triangle with exclamation mark signifies that a TCP/IP Remote Control session is active.

Note: No front panel indication is shown when a serial or modem based remote control session is in progress!

Headphone Level Control

A standard ¼” stereo headphone jack located at the lower left corner of the front panel allows the processed signal to

be monitored, and a Headphone volume level control is available in each submenu. When the headphone volume

control slider is highlighted, clicking changes the jog-wheel into a headphone volume control. Once the headphone

volume is adjusted to your liking, clicking the jog-wheel exits the volume adjustment mode, returning the jog-wheel

back to Highlight Mode.

Note: The headphone amplifiers are fed from the same high quality, 24-bit D to A converter as the analog XLR

outputs. Therefore, the overall Headphone volume will also be affected by the setting of the Peak Output Level

controls in the Output Menu.

Содержание Omnia-6EX






























































































































Результаты поиска

Содержание Omnia-6EX

Отзывы:

Похожие инструкции для Omnia-6EX

Бренды по названию

Популярные бренды

Omnia Omnia-6EX, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Omnia-6EX

Отзывы:

Похожие инструкции для Omnia-6EX

Бренды по названию

Популярные бренды