Page - 3
Table of Contents
Introduction ............................................................................. 4-7
Status Light, Valet Switch & Transmitter
System Versatility -
An Important Note ........................................
7
Using the AL-1610-EDP System .............................................. 8
Arming Using the Transmitter ................................................ 7-8
Arming Bypass, Sensor Bypass
Automatic “Last Door Arming” of the System ...................... 9-10
While the System is Armed, and should it Trigger ................ 10-11
Prewarning Detection Circuit
Disarming the System Using the Transmitter ......................... 11-12
Safety Disarm Feature; Activation Alert; Automatic Rearming
Disarming By Emergency Override ....................................... 12-13
Remote Panic Feature ............................................................. 13-14
Remote Engine Starting .......................................................... 14-17
Safety Features, Stick Shift Remote Starting; Pit-Stop; Turbo Timer
Other Transmitter Operations ................................................. 18
2nd Channel, 3rd Channel, Silent Arming & Disarming
,
Sensor Bypass
Using the Valet Switch ........................................................... 19-20
Alarm Valet Mode & Starting Valet Mode
SecureCode .............................................................................. 21
The Status Light ...................................................................... 22-23
Anti-Carjacking Protection ..................................................... 24-25
Transmitter Protection ............................................................. 25
How to Program Transmitters ................................................. 25-26
How to Program Features ....................................................... 27-28
User Programmable Features .................................................. 29-37
Installer Programmable Features ............................................ 38-42
Complete Programmable Features Matrix .............................. 43
Limited Lifetime Warranty .............................................. Back Cover
for the voltage sensing type of starter output operation. There are four
different base starter output settings. While the default-set minimum is
sufficient for most vehicles; the Extended Starter Cranking Time can be
used for difficult-to-start engines. This feature should only be pro-
grammed by the installer.
Note: “Base timing” is the maximum time period that the AL-1610-EDP will
engage the starter, but only if it does not detect the engine has started
running.
Feature #10 Gasoline Or Diesel Engine
Factory Default Setting
Gasoline (press “arm/lock” button to program)
Option:
Diesel (press “disarm/unlock” button to program)
This feature changes the system's timing of the ignition and starter output
sequence for remotely starting vehicles with a diesel engine. This feature
should only be programmed by the installer.
Feature #8 Programmable Remote Start Relay
Factory Default Setting
Ignition Output
(press “arm/lock” button to program)
Options:
Accessory Output
(press “disarm/unlock” button to program)
Starter Output
(press
“
||” bu
t
ton to program)
The AL-1610-EDP features 4 dedicated remote start output relays, one of
which is programmable (this is the unit’s large blue output wire). Operation
choices are ignition, accessory or starter power output. This feature
should only be programmed by the installer.
Feature #9 Arm, Disarm or Additional Channels
Factory Default Setting
Arm / Disarm
(press “arm/lock” button to program)
Options:
Arm / Channel 5
(press “disarm/unlock” button to program)
Channel 4 / Disarm
(press
“
||” bu
t
ton to program)
Channel 4 / Channel 5
(press red
“
|||”
b
utton to program)
The AL-1610-EDP has outputs designed for arming and/or disarming a
factory-equipped security system. These wires may be used instead to
provide further system outputs, which are remotely operated by the trans-
mitter. These outputs are in addition to the 2nd channel and 3rd channel
outputs, the operation of these outputs is explained on page 18.
As shown in the programming assignment, the arm, disarm, channel 4
and channel 5 are programmable as various combinations. For example,
if the disarm output is needed, but not the arm output, then channel 4 may
be made available for use.
Page - 42
