![background image](http://html1.mh-extra.com/html/omega/cn616tc1/cn616tc1_user-manual_737599026.webp)
Select ALL Zones
to Start Profile Run
=>
48
Enter Setup mode
Select Function 79
EXAMPLE: Start Profile
[Function 79]
=>
=>
Action
Display Before Display After
Buttons to use
together
To run RAMP AND SOAK CN616TC1 MODEL the mode must
be set to 51 or 52[Function 71\31]. Number of segments must be
set for each enabled zone[Function 74]. Setting the number of
segments to “00” will set that zone to run in STANDARD mode.
PROFILE can only be started from Function 79 or the software.
NOTE: For each zone until the PROFILE is started the controller
will run that zone in STANDARD MODE, controlling at the
STANDARD MODE setpoint.
Function 79 will start the profile for any single zone, or all zones
at once. In the first segment the starting setpoint is set at the
ambient temperature and is changed at the rate of slope of the
first segment until the first segment setpoint is reached.
Enter
Select ONE Zone
to Start Profile Run
=>
=>
=>
Enter
=>
[Start run on all enabled zones
with 1 or more segments in the Profile]
OR
Enter
[Start zone 5 Profile]
0 4 0 3
5 1
1
7 1
7 0
7 9
7 9
0
7 9
0 5
7 9
0
7 9
0 7
7 9
7 1
7 0
7 9
0
7 9
5
0 4 0 3
5 1
1
7
0 4 0 3
5 1
1
2.
1.
3.
3.
IMPORTANT!! To avoid overheating, zones intended for Profile
run MUST have their Standard Setpoints set to 0. [Function 36]
7 5
7 0
7 0
7 5
7 5
7 5
0 1
0 1
0 0 0
0 1
1
0 1.5
0 1
1
Enter
Confirm Selection
Enter
Set Temperature
Setpoint
Enter
Set Slope
(degrees/min)
Enter
At any time EXIT
Function
7 5
0 1.5
=>
=>
=>
7 0
7 5
=>
=>
0 1
=>
0 0 0 0
1
=>
0 0.0 0
0 1
1
together
0 1
1
1
0 0 0 0
0 4 0 0
0 4 0 0
0 1
1
0 0 0 0
0 1
1
0 1.5
0 1
1
Set Time
(hours)
Enter and go to Next segment
setpoint [Repeat Steps 4-6 for
all set segments]
0 0.0 0
=>
=>
0 0 0 0
0 2
1
0 1.5
0 8
6
=>
After last segment [set by function 74] go to next zone(Step 4.)
47
0 4 0 3
5 1
1
use &
to set # to 0000-9999
use &
to set # to 00.0-99.9
use &
to set # to 00.00-99.99
3.
4.
5.
6.
Example: Program a profile with one segment in Zone 1 and two
segments in Zone 2 use Function 74 to set Zone 1 to 01 and Zone
2 to 02
(
make sure Zones 1 & 2 are enabled [Function 71\31]
any
enabled Zones 3-6 with 00 segments will run under Standard Control)
. Next
use Function 75 to program the Temperature Setpoint in Zone 1
Segment 1 to 300°(Step 4.) Set the Slope to 15.0°/min(Step 5.)
Set the Time to 05.00/min(Step 6.) (Time is ignored for control
purposes when the Slope(Step 5.) in the segment is not 0.00°/min
)
There are no other segments in Zone 1. Press enter in Step 6. the
Zone display(lower left) on the controller will change to program
Zone 2 Segment 1(Step 4.)
Program the settings for Zone 2.
Start
the profile with Function 79.(A Zone will maintain the Tempera-
ture of the end segment in a profile indefinitely in
Ramp&Soak
2)
7.
Содержание CN616TC1
Страница 9: ...13 14 ...