manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Руководство по обслуживанию

Многофункциональное устройство Olivetti d-Copia 3002MF Plus - надежный помощник в офисе. Улучшите производительность вашего бизнеса, загрузив бесплатное сервисное руководство с нашего сайта. Узнайте все функции и возможности этого устройства для достижения высоких результатов в работе. Будьте уверены в качестве скачанных инструкций с manualshive.com.

Поделиться
Скачать
background image

4

A

6

8

7

A

3.

Secure the mailbox (A) using the two screws 
M4x12 (E).

4.

Remove the rear cover (6) of the mailbox 
(A).

5.

Plug the connector (7) of the mailbox (A) into 
the connector (8) of the machine body.

6.

Reinstall the rear cover (6) of the mailbox 
(A).

3.

Fixer la boîte à lettres (A) à l'aide de deux vis 
M4x12 (E).

4.

Retirer le couvercle arrière (6) de la boîte à 
lettres (A).

5.

Brancher le connecteur (7) de la boîte à 
lettres (A) dans le connecteur (8) du corps 
de la machine.

6.

Remonter le couvercle arrière (6) de la boîte 
à lettres (A).

3.

Fije el buzón de correo (A) con dos tornillos 
M4x12 (E).

4.

Quite la cubierta posterior (6) del buzón de 
correo (A).

5.

Enchufe el conector (7) del buzón de correo 
(A) al conector (8) del cuerpo de la máquina.

6.

Vuelva a instalar la cubierta posterior (6) del 
buzón de correo (A).

3.

Sichern Sie die Mailbox (A) mit zwei 
Schrauben M4x12 (E).

4.

Entfernen Sie die hintere Abdeckung (6) der 
Mailbox (A).

5.

Stecken Sie den Stecker (7) der Mailbox (A) 
in die Steckbuchse (8) des Gerätegehäuses.

6.

Bringen Sie die hintere Abdeckung (6) der 
Mailbox (A) wieder an.

3.

Fissare la mailbox (A) utilizzando le due viti  
M4x12 (E).

4.

Rimuovere il coperchio posteriore (6) della 
mailbox (A).

5.

Collegare il connettore (7) della  mailbox (A) 
al connettore (8) del corpo macchina.

6.

Reinstallare il coperchio posteriore (6) della 
mailbox (A).

3.

ビス M4×12(E)2 本で、

メールボックス (A)

を固定する。

4.

メールボックス (A) の後カバー(6) を取り
外す。

5.

メールボックス (A) のコネクター(7) を機
械本体のコネクター (8) に接続する。

6.

メールボックス (A) の後カバー(6) を元通
りに取り付ける。

3.

使用两个螺丝 M4x12（E）固定邮箱（A）。

4.

拆下邮箱 (A) 的后部盖板 (6)。

5.

将邮箱（A）的接插件（7）插入机器的接插件 

（8）。

6.

重新安装邮箱（A）的后盖板（6）。

3.

M4x12 나사 (E) 두 개를 사용하여 메일박스
(A) 를 고정합니다 .

4.

메일박스 (A) 의 뒤커버 (6) 를 떼어냅니다 .

5.

메일박스 (A) 의 커넥터 (7) 를 본체의 커넥터 
(8) 에 연결합니다

6.

메일박스 (A) 의 뒤커버 (6) 를 다시 장착합니
다 .

E(M4x12)

A

Содержание d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для d-Copia 3002MF plus

Xerox All in One Printer Product Safety Data Sheet preview
All in One Printer
Бренд: Xerox Страницы: 3
Xerox 220 Quick Install Manual preview
220
Бренд: Xerox Страницы: 8
Labau TM200 User Manual preview
TM200
Бренд: Labau Страницы: 19
Konica Minolta bizhub C250i Quick Manual preview
bizhub C250i
Бренд: Konica Minolta Страницы: 61
Xerox B210DNI User Manual preview
B210DNI
Бренд: Xerox Страницы: 205
Xiamen Hanin Electronic Technology HM-A400 User Manual preview
HM-A400
Бренд: Xiamen Hanin Electronic Technology Страницы: 62
Axiohm A794 Setup Manual preview
A794
Бренд: Axiohm Страницы: 8
Xerox WorkCentre M55 Installation And Operation preview
WorkCentre M55
Бренд: Xerox Страницы: 3
Oakton 35622 Series Operating Instructions Manual preview
35622 Series
Бренд: Oakton Страницы: 8
Xerox WorkCentre 7970 System Administrator Manual preview
WorkCentre 7970
Бренд: Xerox Страницы: 268
Phoenix Contact THERMOMARK ROLLMASTER 300 User Manual preview
THERMOMARK ROLLMASTER 300
Бренд: Phoenix Contact Страницы: 42
GeBe GPT-4454 User Manual preview
GPT-4454
Бренд: GeBe Страницы: 25
Kyocera ECOSYS M2635dw Frequently Asked Questions Manual preview
ECOSYS M2635dw
Бренд: Kyocera Страницы: 72
Xerox WorkCentre 5687 Evaluator Manual preview
WorkCentre 5687
Бренд: Xerox Страницы: 28
Carl Valentin Dynacode II IP107 Operating Manual preview
Dynacode II IP107
Бренд: Carl Valentin Страницы: 168
Xerox 7400DX - Phaser Color LED Printer Setup Manual preview
7400DX - Phaser Color LED Printer
Бренд: Xerox Страницы: 2
Polaroid PLR-P3001-N User Manual preview
PLR-P3001-N
Бренд: Polaroid Страницы: 93
Xerox WORKCENTRE C2424 Service Manual preview
WORKCENTRE C2424
Бренд: Xerox Страницы: 432

Бренды по названию

Популярные бренды

Загрузить еще бренды