manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Руководство по обслуживанию

Многофункциональное устройство Olivetti d-Copia 3002MF Plus - надежный помощник в офисе. Улучшите производительность вашего бизнеса, загрузив бесплатное сервисное руководство с нашего сайта. Узнайте все функции и возможности этого устройства для достижения высоких результатов в работе. Будьте уверены в качестве скачанных инструкций с manualshive.com.

Поделиться
Скачать
background image

23

a

m

l

1

2

2.5mm

2

2.5mm

[Checking the leading edge timing]

1.

Check the gap between line (1) on original (a) and line (2) of copy 
example. If the gap exceeds the reference value, adjust the gap 
according to the following procedure.
<Reference value>
Vertical gap of line (2): within ±2.5 mm

2.

Use the maintenance mode U071 to adjust the timing.
Front Head: Adjusts the leading edge timing (surface)
Front Tail: Adjusts the trailing edge timing (surface)
Back Head: Adjusts the leading edge timing (rear side)
Back Tail: Adjusts the trailing edge timing(rear side)

[Vérification de la synchronisation du bord avant]

1.

Vérifier l’écart entre la ligne (1) de l’original (a) et la ligne (2) de l’exem-
ple de copie. Si l’écart excède la valeur de référence, le régler selon la 
procédure suivante.
<Valeur de référence>
Écart vertical de la ligne (2) : ±2,5 mm

2.

Pour régler la synchronisation, utilisez le mode entretien U071.
Front Head: Permet de régler la synchronisation du bord de tête (surface)
Front Tail: Permet de régler la synchronisation du bord arrière (surface)
Back Head: Permet de régler la synchronisation du bord de tête 

(arrière)

Back Tail: Permet de régler la synchronisation du bord arrière 

(arrière)

[Cambio de la sincronización de borde superior]

1.

Compruebe la separación entre la línea (1) del original (a) y la línea (2) 
del ejemplo de copia. Si la separación supera el valor de referencia, 
ajústela siguiendo este procedimiento.
<Valor de referencia>
Separación vertical de la línea (2): dentro de ±2,5 mm

2.

Para ajustar la sincronización utilice el modo de mantenimiento U071.
Front Head: Ajusta la sincronización del borde superior (anverso).
Front Tail: Ajusta la sincronización del borde inferior (anverso).
Back Head: Ajusta la sincronización del borde superior (reverso).
Back Tail: Ajusta la sincronización del borde inferior (reverso).

[Überprüfen des Vorderkanten-Timings]

1.

Den Abstand zwischen der Linie (1) des Originals (a) und der Linie (2) 
des Kopierbeispiels prüfen. Wenn der Abstand größer als der     
Bezugswert ist, den Abstand mit dem folgenden Verfahren einstellen.
<Bezugswert>
Vertikaler Abstand der Linie (2): Innerhalb ±2,5 mm

2.

Zum Einstellen des Timing den Wartungsmodus U071 verwenden.
Front Head: Zur Einstellung des Vorderkanten-Timing (Oberfläche)
Front Tail: Zur Einstellung des Hinterkanten-Timing (Oberfläche)
Back Head: Zur Einstellung des Vorderkanten-Timing  (Rückseite)
Back Tail: Zur Einstellung des Hinterkanten-Timing  (Rückseite)

[Controllo della sincronizzazione del bordo principale]

1.

Verificare lo scostamento fra la linea (1) sull’originale (a) e la linea (2) 
dell’esempio di copia. Se lo scostamento supera il valore di riferimento, 
regolare lo scostamento stesso seguendo questa procedura.
<Valore di riferimento>
Scostamento verticale della linea (2) compreso fra ±2,5 mm

2.

Usare la modalità di manutenzione U071 per regolare la 
sincronizzazione.
Front Head: Regola la sincronizzazione del bordo principale (superficie)
Front Tail: Regola la sincronizzazione del bordo di uscita (superficie)
Back Head: Regola la sincronizzazione del bordo principale  (lato posteri-
ore)
Back Tail: Regola la sincronizzazione del bordo di uscita  (lato posteri-
ore).

[ 先端タイミング確認 ]

1.

原稿 (a) の線 (1) とコピーサンプルの線 (2) のずれを確認する。ずれ
が基準値外の場合、

次の手順で調整を行う。

＜基準値＞
線 (2) の上下ずれ：±2.5mm 以内

2.

メンテナンスモード U071 をセットし、

調整を行う。

Front Head ：先端タイミング ( 表面 ) を調整する
Front Tail ：後端タイミング ( 表面 ) を調整する
Back Head： 先端タイミング ( 裏面 ) を調整する
Back Tail： 後端タイミング ( 裏面 ) を調整する

[ 确认前端定时调整 ]

1.

确认原稿（a）上的线（1）和复印样本上的线（2）之间的偏移值。如果偏
移值超过标准值，则按照下列步骤进行调整。
< 标准值 > 
线（2）的上下偏移值 ：±2.5mm 以内

2.

使用维修模式 U071 调整定时。
Front Head ：调整前端对位 ( 正面 )
Front Tail ：调整后端对位 ( 正面 )
Back Head ：调整前端对位 ( 反面 )
Back Tail ：调整后端对位 ( 反面 )

[ 선단 타이밍확인 ]

1.

원고 (a) 선 (1) 과 벨크로 선 (2) 의 차이를 확인합니다 . 차이가 기준치 
외의 경우 다음 순서로 조정을 합니다 .
＜기준치＞
선 (2) 의 상하차이：±2.5mm 이내

2.

메인터넌스 모드 U071 을 세트하고 조정을 합니다 .
Front Head ：선단 타이밍 ( 표면 ) 을 조정합니다 .
Front Tail ：후단 타이밍 ( 표면 ) 을 조정합니다 .
Back Head ：선단 타이밍 ( 뒷면 ) 을 조정합니다 .
Back Tail ：후단 타이밍 ( 뒷면 ) 을 조정합니다 .

A

B

Содержание d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для d-Copia 3002MF plus

Oki B2200 Setup Manual preview
B2200
Бренд: Oki Страницы: 24
VAF instruments 247 Technical Manual preview
247
Бренд: VAF instruments Страницы: 24
Samsung SCX 4500W - Personal Wireless Laser Multi-Function... User Manual preview
SCX 4500W - Personal Wireless Laser Multi-Function...
Бренд: Samsung Страницы: 113
Canon imageRUNNER ADVANCE 8105 Specification preview
imageRUNNER ADVANCE 8105
Бренд: Canon Страницы: 5
Canon imageCLASS MF269dw Setup Manual preview
imageCLASS MF269dw
Бренд: Canon Страницы: 32
Samsung ML-7300N User Manual preview
ML-7300N
Бренд: Samsung Страницы: 158
Oki C931dn Manuel D'Utilisation preview
C931dn
Бренд: Oki Страницы: 320
Xerox DocuPrint C2200 User Manual preview
DocuPrint C2200
Бренд: Xerox Страницы: 200
Konica Minolta bizhub C227 Installation Manual preview
bizhub C227
Бренд: Konica Minolta Страницы: 12
Output Technology EuroLine Series Operator'S Manual preview
EuroLine Series
Бренд: Output Technology Страницы: 73
SEWOO LK-PXX User Manual preview
LK-PXX
Бренд: SEWOO Страницы: 12
Oce VarioLink 2650cp Quick Setup Manual preview
VarioLink 2650cp
Бренд: Oce Страницы: 2
Kyocera Mita Ecosys FS-1800+ Installation Manual preview
Ecosys FS-1800+
Бренд: Kyocera Mita Страницы: 31
3nStar RPT008 Programmer'S Manual preview
RPT008
Бренд: 3nStar Страницы: 44
Citizen CBM-810 User Manual preview
CBM-810
Бренд: Citizen Страницы: 32
Canon varioPRINT 6000 TITAN Series Manual preview
varioPRINT 6000 TITAN Series
Бренд: Canon Страницы: 69
Canon WS8400 Service Manual preview
WS8400
Бренд: Canon Страницы: 224
Canon Your MX892 Setting Up preview
Your MX892
Бренд: Canon Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды