manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Руководство по обслуживанию

Поделиться
Скачать
Olivetti d-Copia 3002MF plus Скачать руководство пользователя страница 675

7

13

12

Adjusting the height

1.

Check that the respective heights of the pins 
(12) on the connecting plate installed on the 
machine and the connecting holes (13) on 
the document finisher comply with the refer-
ences below.

Compliant: The diameter (a) of the pin (12) is within the height range (b) of the curved section (21).
Non-compliant: The diameter (a) of the pin (12) is extends beyond the height range (b) of the curved 
section (21).
If the heights are non-compliant, use the procedure below to adjust the height.

Réglage de la hauteur

1.

Vérifiez que les hauteurs respectives des 
ergots (12) sur la plaque de connexion 
installée sur la machine et les trous de con-
nexion (13) sur le finisseur de document 
sont conformes aux références ci-dessous.

Bon : Le diamètre (a) de l'ergot (12) est dans les limites de hauteur (b) de la partie courbée (21).
Mauvais : Le diamètre (a) de l'ergot (12) dépasse les limites de hauteur (b) de la partie courbée (21).
Si la hauteur n'est pas conforme, l'ajuster en procédant comme indiqué ci-dessous.

Ajuste de la altura

1.

Compruebe que las alturas correspondien-
tes de las clavijas (12) de la placa de fijación 
instaladas en la máquina y los orificios de 
conexión (13) del finalizador de documentos 
cumplen las referencias de abajo.

Cumple: el diámetro (a) de la clavija (12) está dentro del rango de altura (b) de la sección curvada 
(21).
No cumple: el diámetro (a) de la clavija (12) sobrepasa el rango de altura (b) de la sección curvada 
(21).
Si las alturas no cumplen con las especificaciones, utilice el siguiente procedimiento para ajustar la 
altura.

Einstellen der Höhe

1.

Überprüfen Sie, dass die jeweilige Höhe der 
Stifte (12) der am Gerät installierten Verbind-
ungsplatte und Verbindungsöffnungen (13) 
des Finishers mit den unten angegebenen 
Werten übereinstimmen.

Korrekt: Der Durchmesser (a) des Stifts (12) befindet sich im Höhenbereich (b) des Kurvenabschnitts 
(21).
Nicht korrekt: Der Durchmesser (a) des Stifts (12) ragt über den Höhenbereich (b) des Kurvenab-
schnitts (21) hinaus.
Falls die Höhen nicht korrekt sind, müssen Sie sie wie folgend einstellen.

Regolazione dell'altezza

1.

Controllare che le rispettive altezze dei perni 
(12) sulla piastra di connessione installata 
sulla macchina e i fori di connessione (13) 
sulla finisher documenti corrispondano ai 
riferimenti mostrati sotto.

Conformità: Il diametro (a) del perno (12) è compreso nella gamma di altezza (b) della sezione cur-
vata (21).
Non conformità: Il diametro (a) del perno (12) si estende oltre la gamma di altezza (b) della sezione 
curvata (21).
Se le altezze sono non corrispondenti, utilizzare la procedura riportata sotto per regolare l'altezza.

高さ調整

1.

機械本体に取り付けた連結板のピン (12) と
ドキュメントフィニッシャーの連結用の穴
(13) の高さが以下の基準に適合するか確認
する。

適 合：ピン (12) の直径 (a) が曲げ部 (21) の高さ (b) の範囲に収まっている。
不適合：ピン (12) の直径 (a) が曲げ部 (21) の高さ (b) の範囲からはみだしている。
不適合の場合は、

以下の手順で調整する。

高度调节

1.

确认机器主机上安装的连接板的销钉 (12) 和
装订器的连接用的孔 (13) 的高度是否符合以
下标准。

符  合：销钉 (12) 的直径 (a) 在弯曲部 (21) 的高度 (b) 的范围内。
不符合：销钉 (12) 的直径 (a) 超出了弯曲部 (21) 的高度 (b) 的范围。
不符合时，通过以下步骤进行调节。

높이조정

1.

본체에 설치된 연결판의 핀 (12) 과 도큐먼트 
피니셔의 연결용 구멍 (13) 의 각 높이가 아
래의 기준에 부합하는지 확인합니다 .

적 합  ：핀 (12) 의 직경 (a) 가 곡선부 (21) 의 높이 (b) 의 범위에 들어간다 .
부적합：핀 (12) 의 직경 (a) 가 곡선부 (21) 의 높이 (b) 의 범위를 넘는다 .
부적합의 경우에는 이하의 순서대로 조정합니다 .

a

b

12

21

a

a

13

21

b

b

Содержание d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды