manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Руководство по обслуживанию

Многофункциональное устройство Olivetti d-Copia 3002MF Plus - надежный помощник в офисе. Улучшите производительность вашего бизнеса, загрузив бесплатное сервисное руководство с нашего сайта. Узнайте все функции и возможности этого устройства для достижения высоких результатов в работе. Будьте уверены в качестве скачанных инструкций с manualshive.com.

Поделиться
Скачать
background image

10

a

b<20mm

b>20mm

1

㸫

㸩

 

20±2.5mm

b

b

Adjusting the leading edge timing

The reference value for the leading edge timing is 20 ±2.5 mm at position (1) in the sample image (a). If the timing is outside this range, perform the fol-
lowing adjustment.

1.

Set maintenance mode U034, select [LSU Out Top] and [Cassette(L)].

2.

Adjust the values.
b<20mm : Increase the setting value. b>20mm : Decrease the setting value.

3.

Press the Start key to confirm the setting value.

Réglage de la synchronisation du bord de tête

La valeur de référence pour la synchronisation du bord de tête est de 20 ±2,5 mm à la position (1) sur l'image d'exemple (a). Si la synchronisation est 
hors de cette plage, procéder au réglage suivant. 

1.

Passer en mode maintenance U034, sélectionner [LSU Out Top] et [Cassette(L)].

2.

Régler les valeurs.
b<20mm : Augmentez la valeur de réglage. b>20mm : Diminuez la valeur de réglage.

3.

Appuyer sur la touche de Start pour confirmer la valeur de réglage.

Cómo ajustar la sincronización del borde superior

El valor de referencia para la sincronización del borde anterior es 20 ±2,5 mm en la posición (1) en la imagen de muestra (a).Si la sincronización estuvi-
era fuera de este rango, haga el siguiente ajuste.

1.

Entre al modo de mantenimiento U034, seleccione [LSU Out Top] y [Cassette(L)].

2.

Ajuste los valores.
b<20mm : Aumente el valor de configuración. b>20mm : Reduzca el valor de configuración.

3.

Pulse la tecla de Start para confirmar el valor de configuración.

Einstellen des Vorderkanten-Timing

Der Bezugswert des Vorderkantenabstands beträgt 20 ±2,5 mm an Position (1) des Beispieldokuments (a). Falls das Timing außerhalb dieses Bereichs 
liegt, ist folgende Einstellung vorzunehmen.

1.

Schalten Sie in den Wartungsmodus U034, wählen Sie [LSU Out Top] und [Cassette(L)].

2.

Die Werte einstellen.
b<20mm : Den Einstellwert erhöhen. b>20mm : Den Einstellwert verringern.

3.

Den Einstellwert durch Drücken der Start-Taste bestätigen.

Regolazione della sincronizzazione del bordo principale

Il valore di riferimento per la sincronizzazione del bordo superiore è pari a 20 ±2,5 mm sulla posizione (1) nell'immagine di esempio (a). Se la sincronizza-
zione è all'infuori di questa gamma, effettuare la regolazione seguente.

1.

Impostare la modalità manutenzione U034, selezionare [LSU Out Top] e [Cassette(L)].

2.

Regolare i valori.
b<20mm : Aumentare il valore dell'impostazione. b>20mm : Diminuire il valore dell'impostazione.

3.

Premere il tasto di Start per confermare il valore dell'impostazione.

先端タイミング調整

先端タイミングは、サンプルイメージ (a) の (1) の位置で基準値は 20±2.5mm。

これから外れるときは以下の調整をおこなう。

1.

メンテナンスモード U034 をセットし、

[LSU Out Top]、[Cassette(L)] を選択する。

2.

設定値を調整する。
b<20mm ：設定値を上げる。

　b>20mm ：設定値を下げる。

3.

スタートキーを押し、設定値を確定する。

前端对位调节

前端对位的基准值在图像样张（a）的（1）位置为 20±2.5mm。超出该范围时，须进行以下调节。

1.

设置维护模式 U034，选择 [LSU Out Top]、[Cassette(L)]。

2.

调整设定值。
b<20mm  ：调高设定值。 b>20mm ：调低设定值。

3.

按 Start 键，以确定设定值。

선단 타이밍 조정
선단 타이밍은 샘플화상 (a) 의 (1) 위치에서 기준치는 20±2.5mm. 여기에서 벗어나는 것은 이하의 조정을 합니다 .

1.

메인터넌스 모드 U034 를 세트하고 [LSU Out Top], [Cassette(L)] 을 선택합니다 .

2.

설정치를 조정합니다 .
b<20mm ：설정치를 높입니다 . b>20mm ：설정치를 내립니다 .

3.

시작키를 누르고 설정치를 확인합니다 .

Содержание d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для d-Copia 3002MF plus

Canon PIXMA MX922 Setting Up preview
PIXMA MX922
Бренд: Canon Страницы: 29
Canon PIXMA MX410 Series Network Setup Troubleshooting preview
PIXMA MX410 Series
Бренд: Canon Страницы: 46
Canon BJC-S9000 Quick Start Manual preview
BJC-S9000
Бренд: Canon Страницы: 65
Canon PIXMA MX372 Getting Started Manual preview
PIXMA MX372
Бренд: Canon Страницы: 4
Canon MX530 series Setting Up preview
MX530 series
Бренд: Canon Страницы: 2
Canon BJC-50 Datasheet preview
BJC-50
Бренд: Canon Страницы: 2
Canon Sure shot 80 tele Remote Ui Manual preview
Sure shot 80 tele
Бренд: Canon Страницы: 39
Canon BJC6500 - BJC 6500 Color Inkjet Printer Paper Manual preview
BJC6500 - BJC 6500 Color Inkjet Printer
Бренд: Canon Страницы: 6
Canon G600 Series Getting Started preview
G600 Series
Бренд: Canon Страницы: 20
Canon imagePROGRAF iPF6450 Manual preview
imagePROGRAF iPF6450
Бренд: Canon Страницы: 35
Canon PIXMA MX340 Series Connection Manual preview
PIXMA MX340 Series
Бренд: Canon Страницы: 11
Canon PIXMA MX340 Series Network Installation Manual preview
PIXMA MX340 Series
Бренд: Canon Страницы: 16
Canon imagePROGRAF iPF6300S Setup Manual preview
imagePROGRAF iPF6300S
Бренд: Canon Страницы: 12
Canon MP980 series Connection Manual preview
MP980 series
Бренд: Canon Страницы: 19
Canon MP980 series Quick Start Manual preview
MP980 series
Бренд: Canon Страницы: 101
Canon iP4700 - PIXMA Color Inkjet Printer Getting Started preview
iP4700 - PIXMA Color Inkjet Printer
Бренд: Canon Страницы: 28
Canon i 320 Setup Instructions preview
i 320
Бренд: Canon Страницы: 2
Canon CX-G6400 Manual preview
CX-G6400
Бренд: Canon Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды