manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Руководство по обслуживанию

Поделиться
Скачать
Olivetti d-Copia 3002MF plus Скачать руководство пользователя страница 197

1-3-130

Contents

Uses the specified originals and automatically adjusts the following items in the scanner and the DP scan-
ning sections.
Scanner section:Original size magnification, leading edge timing, center line, chromatic aberration in main/
sub scanning direction, MTF correction, color/monochrome input gamma, color correction matrix automatic 
adjustment
DP scanning section: Original size magnification, leading edge timing and center line, MTF correction, Input 
gamma, automatic adjustment of color correction matrix

Purpose

Automatically adjusts the scanner and the DP scanning sections.

U411

Scanner auto adjustment
(Message: Scanner Auto Adjustment)

Items

Use

Contents

Original for adjustment

(P/N)

Table (Chart 
A)

In case of losing 
adjustment data, 
differing from the 
color tone 
extremely (not 
improve in case of 
executing U410)   
ISU(CCD unit), 
Optical LED lamp, 
Engine EEPROM, 
when replacing DP 
CIS
Use when setting 
up DP or executing 
U021 initialization

Execute automatic adjusts the table 
scanning.

Magnification in the sub scanning 
direction / Leading edge timing
Center line / chromatic aberration
Sub scanning chromatic aberration / 
MTF correction
gamma in color mode / color correc-
tion matrix
Input gamma in monochrome mode

AVGR14938B

DP 
FU(ChartB) *1

DP 
FD(ChartB) *2

Use when setting 
up DP or executing 
U021 initialization

Execute the 1st side automatic 
adjustment in the DP scanning sec-
tion.
Execute the 2nd side automatic 
adjustment in the DP scanning sec-
tion.

Magnification in the sub-scanning 
direction
Leading edge timing
Center line
Trailing edge timing

AVGR11211F

COL OR SCANN ER

CH ART A4

N o.302K 357010

Y11

8

240-1

Service Manual

Содержание d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды