Olivetti d-Copia 1801MF Plus Скачать руководство пользователя страница 57

Страница: 57 / 492

2NC/2NF/2NG/2NN/3P7/3P8/3P9

1-3-3

Optical

U071 DP Timing

The timing of DP reading are adjusted.

U072 DP Center

The center line of DP reading image are
adjusted.

U074 Adj DP input

The input light volume at the time of DP
reading are adjusted.

U089 Output MIP-PG

PG output is set up.

U099 Detect Org Sz

The setting of sensing threshold value in
the original size detection and operation
are checked.

High
voltage

U100 Main HV Output

Main high voltage, laser, a main motor, etc.
are turned on, and the main high-voltage
operations are checked.

U101 1ST TC Output

References and setup, and outputs of a
high-voltage control value other than main
high voltage are checked.

U108 Adj Sepa Sbias

The ON/OFF timing of separation shift bias
is adjusted.

U110 Drum Cnt

The display of a drum counter is set up.

U111 Drum Time

The display of drum drive time is set up.

U117 Drum No.

Drum serial No. is displayed.

U118 Drum History

A drum history is displayed.

U127 Clr Trans Cnt

The display of a transfer counter is set up.

Developer

U130 Set Toner Install

Installation of a toner is performed.

U135 Chk Toner Motor

Operation of a toner motor is checked.

U139 Temp/Humidity

Displays the temperature and humidity.

U140 Adj Dev bias

Development bias is set up.

U147 Set Toner Apply

Same as the above

U150 Chk Toner Sensor

Display the state of the toner container
sensor SW.

U156 Adj Tnr Ctrl Lv

The amount of supply of a toner is
adjusted.

U157 Dev Time

The time of a developer drive is displayed
and set up.

U158 Dev Cnt

A developer counter is displayed and set
up.

Fuser

U161 Adj Fuser Temp

Fuser control temperature is set up.

U167 Clr Fuser Cnt

A fuser counter is displayed and set up.

U199 Fuser Temp

Fuser temperature, a outside temperature,
and absolute humidity are displayed.

Section

Item

No.

Content of maintenance item

Summary

Содержание d-Copia 1801MF Plus













































































































































































































































































































































































































































































































Результаты поиска

Содержание d-Copia 1801MF Plus

Отзывы:

Бренды по названию

Популярные бренды

Olivetti d-Copia 1801MF Plus, Руководство по обслуживанию

Результаты поиска

Содержание d-Copia 1801MF Plus

Отзывы:

Бренды по названию

Популярные бренды