Olivetti d-Copia 1801MF Plus Скачать руководство пользователя

Страница: 206 / 492

2NC/2NF/2NG/2NN/3P7/3P8/3P9

1-4-34

9000

Document processor com-
munication error

A communication error from
document processor is
detected 10 times in succes-
sion.

DP main PWB

1. Check that the versions of the main unit

firmware and the DP firmware are
identical.

2. Confirm that the wiring connector is

firmly connected and, if necessary,
connect the connector all the way in.
DP main PWB(YC1) and main/engine
PWB (YC18)

3. If the wiring is disconnected, shorted or

grounded, replace the wiring.

4. Replace the DP main PWB

9060

DP EEPROM error

Mismatch of reading data from
two locations occurs 3 times
successively.
Mismatch between writing
data and reading data occurs
3 times successively.

DP main PWB

1. Execute U906 Separating Operation

Release (see page 1-3-114).

2. Confirm that the EEPROM has been

properly installed.

3. Replace the DP main PWB

Device damage of
EEPROM

Contact the Service Support.

F000

Communication error
between Main/Engine PWB
and Operation PWB

Main/Engine PWB

1. Turn the main power swtch off and after

5 seconds, then turn power on.

2. Check that the wirings and connetors

between the main/engine PWB and the
operation PWB are normal.
Main/engine PWB (YC2010) and
operation PWB (YC1)

3. Check that the DIMM memories in the

main/engine PWB are well conducted
and, if not, replace.

4. Execute U021initialize memory. (see

page 1-3-19)

5. Replace the main/engine PWB.

Operation PWB

Replace the operation PWB (see page 2-2-
30).

F020

Main/Engine PWB RAM
check sum error

Main memory
(RAM)

Turn the main power switch off/on to restart
the machine. If the error is not resolved,
replace main/engine PWB (see page 2-2-
11).

Code

Contents

Related parts

Check procedures/

corrective measures

Содержание d-Copia 1801MF Plus













































































































































































































































































































































































































































































































Результаты поиска

Содержание d-Copia 1801MF Plus

Отзывы:

Похожие инструкции для d-Copia 1801MF Plus

Бренды по названию

Популярные бренды

Olivetti d-Copia 1801MF Plus, Руководство по обслуживанию

Результаты поиска

Содержание d-Copia 1801MF Plus

Отзывы:

Похожие инструкции для d-Copia 1801MF Plus

Бренды по названию

Популярные бренды