Olivetti d-Copia 1801MF Plus Скачать руководство пользователя

Страница: 211 / 492

2NC/2NF/2NG/2NN/3P7/3P8/3P9

1-4-39

2. DP-scanning

Defective part

Check description

Corrective Action

Original document

Verify the sides of the original
document.

If the sides of the original document are
reversed, place the original document properly.

Contact glass assy Check the location the contact

glass is mounted.

Re-mount the contact glass if it is hanged off.

FFC cable CIS

Check the FFC cable between
the CIS and main/engine PWB is
properly connected. Or, verify
conduction of the wire.

Reinsert the connector if it its connection is
loose. Or, if conduction is lot, replace the wire.

Home position sen-
sor

Check the location the home
position sensor is mounted.

Re-mount the home position sensor if it is
hanged off.

Scanner drive belt

Check that the scanner drive belt
is loosely mounted.

If the scanner drive belt is loosely mounted,
secure the screws.

Scanner drive gear Check that the scanner drive

gear is loosely mounted.

If the scanner drive gear loosely mounted,
secure the screw.

CIS PWB

The CIS PWB is defective.

Replace the ISU and perform U411.
(see page 1-3-75)

Main/Engine PWB

The main/engine PWB is defec-
tive.

Replace the main/engine PWB.(see page 2-2-
11)

Содержание d-Copia 1801MF Plus













































































































































































































































































































































































































































































































Результаты поиска

Содержание d-Copia 1801MF Plus

Отзывы:

Похожие инструкции для d-Copia 1801MF Plus

Бренды по названию

Популярные бренды

Olivetti d-Copia 1801MF Plus, Руководство по обслуживанию

Результаты поиска

Содержание d-Copia 1801MF Plus

Отзывы:

Похожие инструкции для d-Copia 1801MF Plus

Бренды по названию

Популярные бренды