Oliver 4265 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 70

Oliver 4265 Скачать руководство пользователя страница 6

6 |

Page

Oliver Machinery

4265 Jointer

Introduction

Thank you for choosing Oliver! This manual contains important information on how to safely set up,

operate, and maintain this machine. Please take the time to read through this manual, and make sure you

understand all the instructions.

While this manual may provide tips on optimizing the result of your workpiece, the manual is not intended

as a substitute for formal woodworking training. If you need to know how to safely perform an operation,

please consult knowledgeable and qualified sources before proceeding further.

We made every effort to keep this manual up-to-date. Instructions, specifications, drawings, and

photographs in this manual should match the machine delivered. If you find any differences, or anything

that seems confusing in this manual, or some instructions are not available, please check our website for

an updated version:

WWW.OLIVERMACHINERY.NET/MANUALS

Alternatively, you can contact our technical support for help:

1-800-559-5065

Before calling, please note down the manufacture date and serial
number  of  the  machine.  You  can  find  the  information  on  a
nameplate  located  on  the  back  of  the  machine,  right  above  the
electrical  junction  box.  This  information  is  needed  to  provide
proper technical support, and to determine if an updated manual is
available for your machine.

Please let us know how well this manual serves you. If you have any
suggestions, please call the number above or email us at:

[email protected]

We love to hear from our customers and make improvements.

«
...
4
5
6
7
8
...
»

Содержание 4265







































































Отзывы:

Нет отзывов