Oliver 4265 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 70

Oliver 4265 Скачать руководство пользователя страница 48

48 |

Page

Oliver Machinery

4265 Jointer

Troubleshooting

Problem

Possible Cause

Possible Solution

Machine does not start.

Machine is not

connected to a power

source.

1.

Make sure machine is plugged in, or power
disconnect is at the ON position.

2.

Check electrical panel for tripped circuit
breaker or blown fuse.

3.

Ensure all electrical connections have good
contacts.

Low voltage / current. Have an electrician to check/repair the power

circuit.

Faulty switch/motor/

capacitor.

Contact customer service for further assistance.

Machine trips thermal

protection / circuit

breaker, or blow fuses.

Machine is undersized

for the operation.

Reduce depth of cut and/or feed rate.

Workpiece moisture

level is too high.

Only joint wood with moisture level below 20%.

Machine is jammed.

Make sure cutterhead is not jammed by
woodchips. Check dust chute and clear
blockages.

Too much load on a

circuit.

Make sure power circuit is sized for this
machine. If the same circuit is shared, ensure the
circuit is sized to supply power for all items in
the circuit.

Motor/capacitor

issue.

Contact customer service for further assistance.

Machine stalls during

operation.

Machine is undersized

for the operation.

Reduce depth of cut. Lower feed rate.

Dull cutters

Rotate/replace cutter inserts.

Belt slipping

Clean belt and the pulleys. Adjust belt tension.

Motor/capacitor

issue.

Contact customer service for further assistance.

Machine stopped during

operation.

Thermal overload

protection triggered.

Hit STOP button and wait for at least 3 minutes.
When machine is cooled down, overload
protection will reset automatically. Reduce
depth of cut and feed rate before continue.

Outfeed table is

stuck/difficult to adjust.

Outfeed table is

locked.

Loosen the locking cap screw before adjusting
the outfeed table.

Digital readout not

functional.

Dead battery.

Replace battery.

«
...
46
47
48
49
50
...
»

Содержание 4265







































































Отзывы:

Нет отзывов