Oliver 4265 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 70

Oliver 4265 Скачать руководство пользователя страница 21

4265 Jointer

OLIVERMACHINERY.NET

21

|

Page

Assembly

This jointer is mostly assembled in the factory. There are a few more steps to complete before the machine

is ready for a test run:

1.

Setup control panel.

2.

Install battery for digital readout.

3.

Inspect / Adjust Jointer Tables (optional).

4.

Install cutterhead guard.

5.

Connect jointer to a dust collection system.

6.

Connect jointer to power source.

The approximate time for cleaning and assembly is approximately 60 minutes.

Setup Control Panel

1.

To prevent damages, the control panel is

lowered when it is shipped from the factory.

Please follow the instructions to setup the

control panel:

2.

Remove all six cap screws from control panel

post.

3.

Raise the control panel to its operational

position, then remount it back to the cabinet.

4.

Attach the last two cap screws through the

table adjustment handwheel bracket.

Install Batteries for Digital Readout

Locate the digital readout on the control panel. Remove the battery
cover and install 2 AA sized batteries.

«
...
19
20
21
22
23
...
»

Содержание 4265







































































Отзывы:

Нет отзывов