OKIDATA OL400e Series Скачать руководство пользователя страница 315

Страница: 315 / 397

Page: 196

Service Manual for OL400e/OL410e/OL410e-PS

Chapter 4 Failure & Repair Analysis

RAP 08: Light or Blurred Output

START

Refer to Section 4.5 of this Service Handbook before proceeding

Is the TONER LOW message displayed?

YES

Add toner.

Is the paper used designed for use in laser printers?

Use paper designed for use in laser printers.

YES

Is the lens surface of the LED head dirty?

YES

Clean the lens.

Is the LED head installed properly?

Check connector CN4 of the main controller board

proper connection.

Properly install the LED head.

YES

Is the contact plate of the transfer roller properly
touching the power supply board?

Adjust the transfer roller contact plate to properly
touch the power supply board.

YES

Are the contacts of the developing roller and the contact
of the transfer roller properly touching the contact assembly?

Adjust the contacts of the developing roller and transfer
roller to touch the contact assembly.

YES

Replace the transfer roller.

Has the problem been resolved?

YES

End of procedure.

Replace the image drum cartridge.

Has the problem been resolved?

Содержание OL400e Series





































































































































































































































































































































































Результаты поиска

Содержание OL400e Series

Отзывы:

Бренды по названию

Популярные бренды

OKIDATA OL400e Series, Руководство по обслуживанию

Результаты поиска

Содержание OL400e Series

Отзывы:

Бренды по названию

Популярные бренды