OKIDATA OL400e Series Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 397

OKIDATA OL400e Series Скачать руководство пользователя страница 119

Page: 92

Service Manual for OL400e/OL410e/OL410e-PS

Chapter 3 Maintenance & Disassembly

3.2.02 Upper Cover Assembly

Disassembly

Perform the procedure listed below first.

- 3.2.01(

)

- Release the two thumb screws and remove the PostScript board
OL410e/PS only (1).
- Slide the operator panel (2) in the direction of arrow A, then lift it up to detach
it from the unit.
- Turn the operator panel over.

- Detach the flexible cord (3) from connector CN1 (4) of the contact switch board (5).

- Remove the operator panel.
-

Use a rubber band to pull the wire clips of the interface connector in. This will prevent

damage to the clips when the cover (6) is removed.

- Press the knobs (7) and raise the face-down stacker assembly (8).
- Remove the two screws (9).
- Open the manual feed guide (10).
- Lift the upper cover at the front and tilt it until the back of the cover is free of the two
rear claws.
- Lift the upper cover (6) straight up, then turn it approximately 45 degrees to clear the
raised stacker cover. Refer to View A.
- Remove the upper cover assembly.

NOTE:

Refer to the page following the diagram for installation information.()

«
...
117
118
119
120
121
...
»

Содержание OL400e Series














































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды