Ogden ETR-9040 Скачать руководство пользователя страница 5

Страница: 5 / 24

Common Mode

Rejection Ratio
(CMRR):

120db

Sensor Break

Detection:

Sensor open for TC, RTD and mV

inputs, below 1mA for 4-10 mA input, below 0.25V
for 1-5V input, unavailable for other inputs

Sensor Break

Responding Time:

Within 4 seconds for TC, RTD and

mA inputs, 0.1 second for 4-20 mA and 1-5V inputs

Event Input

Logic Low

-10V minimum, 0.8V maximum

Logic High: 2V minimum, 0.8V maximum
Functions:

Remote reset, remote lockout

Output 1/ Output 2

Relay Rating: 2A/240VAC, life cycles 200,000 for
resistive load
Pulsed Voltage: Source Voltage 5V, current limiting
resistance 66 ohms

Triac (SSR) Output

Rating:

1A/240VAC

Inrush Current: 20A for 1 cycle
Min. Load Current:

50mA rms

Max.Off-state Leakage: 3mA rms
Max. On-state Voltage: 1.5V rms
Insulation Resistance: 1000 Mohms min. at 500VDC
Dielectric Strength: 2500VAC for 1 minute

DC Voltage Supply Characteristics
(Installed at Output 2)

Type

Tolerance

Max. Output

Ripple

Isolation

Current

Voltage

Barrier

20V

± 0.5V

25mA

0.2Vp-p

500VAC

12V

± 0.3V

40mA

0.1Vp-p

500VAC

± 0.15V

80mA

0.05Vp-p

500VAC

Data Communications

Interface:

RS-485 (up to 247 units)

Protocol:

Modbus protocol RTU mode

Address:

1 - 247

Baud Rate:

0.3 ~ 38.4 Kbits/sec

Data Bits:

8 bits

Parity Bit:

None, Even or Odd

Stop Bit:

1 or 2 bits

Communication Buffer: 50 bytes

Environmental& Physical

Operating Temperature: -10°C to 50°C
Storage Temperature:

-40°C to 60°C

Humidity:

0 to 90% RH (non-condensing)

Insulation Resistance: 20 Mohms min. (at 500VDC)
Dielectric Strength: 2000VAC, 50/60Hz for 1minute
Vibration Resistance: 10 - 55Hz, 10m/s

for 2 hours

Shock Resistance:

200m/s

(20g)

Moldings:

Flame retardant Polycarbonate

Dimensions: 48mm(W) x 48mm(H) x 94mm(D),

86mm depth behind panel

Weight:

150 grams

Approval Standards

Safety:

UL873 (11

edition, 1994)

CSA C22.2 No. 24-93
EN61010-1 (IEC1010-1)

Protective Class:

IP30 front panel, indoor use

IP20 housing and terminals (with pro-
tective cover)

EMC:

EN61326

Related Products:
SNA10A—Smart Network Adapter for Third Party

Software. Converts 255 channels of RS-485 or
RS-422 to RS-232 Network

SNA10B—Smart Network Adapter for ETR-Net

Software. Converts 255 channels of RS-485 or
RS-422 to RS-232 Network

NON-VOLATILE MEMORY

• Retains process parameters when power is off

DISPLAY MODE

Indicates value being displayed:

• PV PROCESS VALUE
• HSP1 OUTPUT 1 HIGH LIMIT

SET POINT

• LSP1 OUTPUT 1 LOW LIMIT

SET POINT

• SP2 OUTPUT 2

TOUCH KEY, Sealed mylar front panel

• Splash and chemical resistant

• Tactile feedback, pressure sensitive buttons

FM APPROVED LIMIT CONTROL
• EASY OPERATION
• QUICK SET-UP

CONTROL LOCK
STATUS INDICATOR

STATUS INDICATORS
• OUTPUT 1
• OUTPUT 2
• °C
• °F

Содержание ETR-9040

























Результаты поиска

Содержание ETR-9040

Отзывы:

Похожие инструкции для ETR-9040

Бренды по названию

Популярные бренды

Ogden ETR-9040, Инструкция по эксплуатации

Результаты поиска

Содержание ETR-9040

Отзывы:

Похожие инструкции для ETR-9040

Бренды по названию

Популярные бренды