Octalarm T16 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 56

background image

Installation instructions

Adesys bv, Wateringen, NL

34

Octalarm-T2 / T4 / T8 / T16

17. PROGRAMMING OF INSTALLATION DATA

After the Octalarm has been placed, the installation dependent parameters such as normally open /
normally closed contacts for the alarm inputs, possible delay times and such, have to be set. These
settings take place in the so-called installation program. See part 18 “INSTALLATION PROGRAMS”.
Each Octalarm is supplied with factory defaults, as generally used in practice.

Make a note of every modified setting at the back of this manual in order not to lose the overview
and to avoid future operation errors. For resetting the default settings, see chapter 18.15.Prog 99
“clear all settings”

17.1 Programming options

The Octalarm can be programmed in the following ways:

•

using the operation panel,

•

using a PC at the serial interface (RS-232 connection),

•

through the telephone line using the built-in modem.

•

over the mobile network, using the inbuilt modem (only model -G).

17.1.1 Programming using the operation panel

B

Press the Prog-key continuously until after approximately 5 seconds

PROG 10: set display

contrast display

appears on the display. You are now in the installation program.

B

Select the number of the program that you want to modify or check the settings by using the

E

and

F

keys. Press the Prog-key again in order to start the program. In case a blinking setting or cursor

appears, a selection can be made using the

E

and

F

keys. Use the cursor keys

C

and

D

to move

the cursor around. Confirm each new setting by pressing the Prog-key.

Following each modified setting, you must answer all additional questions until the message

SETTINGS STORED

appears. When the installation program is closed prematurely by using the esc-

key, all former settings will be replaced!

Pressing the Prog-key repeatedly enables you to check the current settings.

During set-up subsequent menus are partly dependent on data entered earlier. Therefore, it is
possible that not all menus described appear on the display during set-up.

17.1.2 Programming using the PC

B

Connect the RS-232 connection of the Octalarm to the serial port (COM port) of the PC using a

serial cable.

B

Launch a terminal emulation program. Examples of such programs are ”Procomm”, “PC+”, “Norton

Commander”, “Telix” etc. Set the following options for the COM port used: 19.200 baud, no parity,
8 bit data, 1 stop bit.

B

Start communication by entering "OT" on the keyboard of the PC. The menu for the Octalarm -T

appears.

«
...
32
33
34
35
36
...
»

Содержание T16

























































Отзывы:

Нет отзывов

Похожие инструкции для T16

Бренд: Eclipse Страницы: 48

Бренд: Eclipse Страницы: 52

Бренд: Eclipse Страницы: 48

Бренд: Far Tools Страницы: 24

Бренд: FAR Страницы: 14

Бренд: Faraday Страницы: 2

Бренд: WATERGUARD Страницы: 2

Бренд: HAI Страницы: 2

Бренд: Xiaomi Страницы: 10

EasyLook PPDF17000

Бренд: Abus Страницы: 23

HiFi Speaker System

Бренд: Eltax Страницы: 2

Бренд: Pentatech Страницы: 26

Бренд: Brickcom Страницы: 40

Бренд: PRODIS Страницы: 12

Motion Sensor Alarm

Бренд: Tiiwee Страницы: 35

Бренд: usi Страницы: 10

Бренд: Vivotek Страницы: 2

Бренд: FLIR Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды