background image

 

 

 

 

 

 

 

 

 

 

 

46 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
All information in this document, including URL and other Internet Web references, is subject to change without notice. 
Complying with all applicable copyright laws is the responsibility of the user. Without limiting the rights under 
copyright, no part of this document may be reproduced, stored in or introduced into a retrieval system, or transmitted 
in any form or by any means (electronic, mechanical, photocopying, recording or otherwise), or for any purpose, 
without the express written permission of Nyfors Teknologi AB. NYFORS may have patents, patent applications, 
trademarks, copyrights, or other intellectual property rights covering subject matter in this document. Except as 
expressly provided in any written license agreement from NYFORS, the furnishing of this document does not give you 
any license to these patents, trademarks, copyrights, or other intellectual property. Nyfors Teknologi AB grants the 
purchaser of this product the right to reproduce one (1) copy of this user manual for each hardware device in the 
package. 
 
© 2020 Nyfors Teknologi AB. All rights reserved. 
 
NYFORS, AUTOCLEAVER, AUTOCLEAVER LDF, CLEAVEMETER and MEGAPIXEL VIEWER are either registered trademarks 
or trademarks of Nyfors Teknologi AB in Sweden and/or other countries. All other brands and product names are 
trademarks or registered trademarks and property of their respective owner. 

Содержание AUTOCLEAVER LDF















































Отзывы: