NXP Semiconductors P5010 Скачать руководство пользователя страница 67

Страница: 67 / 77

P5040/P5020 Reference Design Board User Guide, Rev. 0

Freescale Semiconductor

Programming Model

NOTE

SW registers do NOT reflect the content of physical switches.

Figure 45. Switch Register (PX_SW(1:8))

7.1.25

Switch Enable Register (PX_ENx)

The switch enable register selects the bit source PX_SWx register or corresponding switches.

Figure 46. Switch Enable Register (PX_EN(1:8))

SWx #1

SWx #2

SWx #3

SWx #4

SWx #5

SWx #6

SWx #7

SWx #8

Reset

Offset

0x20, 0x22, 0x24,...

Table 53. PX_SW (1:8) Field Descriptions

Bits

Name

Description

0–7

SWx #b

Values that will replace switch SWx #b.

ENx #1

ENx #2

ENx #3

ENx #4

ENx #5

ENx #6

ENx #7

ENx #8

Reset

Offset

0x21, 0x23, 0x25,...

Table 54. PX_EN(1:8) Field Descriptions

Bits

Name

Description

0–7

ENx #b

• 0 - External switch SWx #b controls a corresponding configuration pin; the

value is unaffected by the system controller.

• 1 - Internal register SWx #b controls a corresponding configuration pin; the

value is unaffected by the external switches.

Содержание P5010














































































Результаты поиска

Содержание P5010

Отзывы:

NXP Semiconductors P5010, Руководство пользователя, Страница: 67 / 77

Результаты поиска

Содержание P5010

Отзывы: