NXP Semiconductors P5010 Скачать руководство пользователя страница 63

Страница: 63 / 77

P5040/P5020 Reference Design Board User Guide, Rev. 0

Freescale Semiconductor

Programming Model

Figure 39. Configuration Sequencer Status Register (PX_VSTAT)

7.1.19

P5040/P5020RDB Status Register (PX_HSTAT)

The P5040/P5020RDB status register can be used to monitor optional connectivity.

Figure 40. P5040/P5020RDBP5040/P5020RDB Status Register (PX_HSTAT)

7.1.20

OCM Control/Status Register (PX_OCMCSR)

The OCM control/status register is a general-purpose R/W register that communicates between
P5040/P5020 and the FPGA GMSA processor.

—

BUSY

Reset

Offset

0x11

Table 46. PX_VSTAT Field Descriptions

Bits

Name

Description

0–6

—

Reserved

BUSY

• 0 - VELA sequencer is idle.
• 1 - VELA sequencer is busy.

—

PRESENT

_1588

NAND_TYPE

Reset

Offset

0x12

Table 47. PX_HSTAT Field Descriptions

Bits

Name

Description

0–5

—

Reserved

PRESENT_1588

• 0 - Detects 1588 riser card
• 1 - No riser card

NAND_TYPE

• 0 - Micron MT29F4G08ABADAWP:D
• 1 - Numonix NAND08GW3B2CN1E

Содержание P5010














































































Результаты поиска

Содержание P5010

Отзывы:

NXP Semiconductors P5010, Руководство пользователя, Страница: 63 / 77

Результаты поиска

Содержание P5010

Отзывы: