NXP Semiconductors P5010 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 77

NXP Semiconductors P5010 Скачать руководство пользователя страница 18

P5040/P5020 Reference Design Board User Guide, Rev. 0

18

Freescale Semiconductor

Architecture

5.1.7

enhanced Secure Digital Host Controller (eSDHC) &
embedded Multi Media Controller (eMMC)

The P5040/P5020 processor has an eSDHC and an eMMC controller, which the P5040/P5020 connects to
an SD media card slot. The I

2

C3_SDA signal uses write protect (WP). The I

2

C3_SCL signal uses card

detect (CD). The DS supports the following:

•

1.8, 2.5, and 3.3V SD/eMMC media card voltages.

•

x4-bit and x8-bit cards though the latter uses SPI_CS[0:3] signals as eSDHC_DAT[4:7].

— eSDHC_DAT[4:7] signals are shared with SPI CS pins.

— Software can route the pins to either eSDHC/eMMC cards or SPI devices; however, they

cannot be used simultaneously.

CAUTION

Insert an SD/eMMC media card suited to P5040/P5020 CVDD voltage.

5.1.8

UART Serial Ports

Two RS-232 transceivers on the P5040/P5020RDB contribute to user application development and
provide convenient communication channels to both terminal and host computers. The transceivers are
connected to P5040/P5020 dedicated UART ports: one provides interconnection to DUT UART1/3 ports
or ngPIXIS FPGA; the other explores UART2/4 dedicated ports.

Analog Devices’ ADM561JRSZ product internally generates required RS-232 levels from 3.3V_HOT
supply.

NOTE

Powering from the 3.3V_HOT power rail is possible even when
P5040/P5020 is powered down. Thus, the FPGA processor can run
programs and interact with the user while allowing board reconfiguration
while sealed in the chassis.

This table describes the P5040/P5020RDB RS-232 interface

.

Table 8. eSPI Slave devices

Device

Clock Frequency

(MHz)

Voltage Range (V)

Capacity

SPI CS

Spansion

S25FL129P0XNFI001

104

2.7–3.3

16 MB

CS[0,1]

Microchip

25AA1024T-I/SM

2, 10, 20

1.8–3.3

128 KB

CS2

1588 Riser Card

—

1.8–3.3

—

CS3

«
...
16
17
18
19
20
...
»

Содержание P5010














































































Отзывы:

Нет отзывов