NXP Semiconductors P5010 Скачать руководство пользователя страница 64

Страница: 64 / 77

P5040/P5020 Reference Design Board User Guide, Rev. 0

Freescale Semiconductor

Programming Model

NOTE

Not supported for P5040/P5020RDB.

Figure 41. Configuration Sequencer Status Register (PX_OCMCSR)

NOTE

Software sets the values. Use different software in the GMSA processor to
redefine the values.

7.1.21

OCM Message Register (PX_OCMMSG)

The OCM message register is a general-purpose R/W register used to communicate between P5040/P5020
and the FPGA GMSA processor.

NOTE

Not applicable for P5040/P5020RDB.

Figure 42. Configuration Sequencer Status Register (PX_OCMMSG)

ACK

DBGSEL

MSG

Reset

Offset

0x14

Table 48. PX_OCMCSR Field Descriptions

Bits

Name

Description

ACK

• 0 - No acknowledgement
• 1 - OCM software signals that message has been processed.

Unassigned values

2–5

DBGSEL

Selects information for the GMDBG register.

Unassigned values

MSG

• 0 - No message
• 1 - Software-initiated signal notifies OCM of a message.

MSGADDR

Reset

Offset

0x15

Содержание P5010














































































Результаты поиска

Содержание P5010

Отзывы:

NXP Semiconductors P5010, Руководство пользователя, Страница: 64 / 77

Результаты поиска

Содержание P5010

Отзывы: