manualshive.com logo in svg

NXP Semiconductors P5010, Руководство пользователя, Страница: 19 / 77

Поделиться
Скачать
NXP Semiconductors P5010 Скачать руководство пользователя страница 19

P5040/P5020 Reference Design Board User Guide, Rev. 0

Freescale Semiconductor

19

 

Architecture

5.1.9

USB Interfaces

The P5040/P5020 has dual HS USB transceivers whose main features are as follows:

•

Compliance with USB Specification, USB Rev. 2.0.

•

USB 2.0 Transceiver Macrocell Interface (UTMI) with Link Controller.

•

Supports HS, FS, and LS modes of operation.

•

Supports signalling.

•

Supports Host and Device modes.

— Working in Host mode only, the RDB connects a USB transceiver to connector Type A thus 

enabling communication with keyboards, mice, memory sticks, etc. 

— Working in Host and Device modes, a second USB transceiver connects to a second Type A 

connector which has bus signal connecting directly to the P5040/P5020 internal PHY.

The 24MHz USB block reference clock provides additional control to the P5040/P5020 in conjunction 
with the USB power sequence. GPIO 4,6 control the VBUS Drive. GPIO 5,7 get Power Fault indications 
via the FPGA. 

This figure shows the P5040/P5020RDB USB interface.

Table 9. P5040/P5020RDB RS232 Interface

UART Ports

Destination

Power supply

Flow control

External Connector

UART1

Terminal (Host 

Computer)

3.3V_HOT

Supported

UART1/3 (J5 Bottom)

UART3

Unsupported

UART2

Supported

UART2/4 (J5 Top)

UART4

Unsupported

Содержание P5010














































































Отзывы:

Нет отзывов