manualshive.com logo in svg

NXP Semiconductors P5010, Руководство пользователя, Страница: 30 / 77

Поделиться
Скачать
NXP Semiconductors P5010 Скачать руководство пользователя страница 30

P5040/P5020 Reference Design Board User Guide, Rev. 0

30

Freescale Semiconductor

 

Architecture

•

CS0, CS1, or CS2 select NOR FLASH depending on “CFG_Vbank[0...2]”.

•

FPGA-generated signals are used to re-arrange internal addresses as per user configuration options 
“CFG_LBMAP[0...3]”.

5.1.16.3

NAND FLASH

Micron NAND FLASH memory (MT29F4G08ABADAWP:D) has 512 MB and an 8-bit data width. 
NAND FLASH is controlled by the FCM Local Bus. 

•

FLASH R/B output indicates the status of a device operation. This open drain output connects to 
the P5040/P5020 LFR/B/LGPL4 line.

•

CS0, CS2, or CS[4:6] select NAND FLASH as per “CFG_LBMAP[0...3]”.

5.1.16.4

PromJet Connector

A PromJet connector can be used for debugging purposes. 

Perpiherals and embedded storage can be 

connected to the PromJet superset connector. The 16-bit PromJet modules (FLASH memory emulators) 
are available from Emutec. See www.emutec.com.

CS0 or CS1 select between PromJet FLASH and onboard FLASH as per “CFG_LBMAP[0...3]”.

5.1.17

Debug Features

The reference board provides a JTAG COP header and AURORA test points for debug purposes, using the 
CodeWarrior USBTAP already installed in the system.

To upgrade the U-Boot stored on the NOR FLASH, use the CodeWarrior USBTAP tool. 

5.1.18

Clock

For a description of the clock architecture, see 

Section 5.4, “Clocks

.”

5.1.19

Temperature Anode and Cathode

The P5040/P5020 has two pins, Temp_Anode and Temp_Cathode, connected to a thermal body diode on 
the die that allow direct temperature measurement. The pins are connected to an ADT7461 thermal 
monitor that allows direct die temperature readings with an accuracy of ±1 °C.

5.1.20

Power

For a description of the clock architecture, see 

Section 5.3, “System Power Connections

.”

5.2

System Control Logic 

The P5040/P5020RDB contains FPGA ngPIXIS that implements the following functions:

•

Resets sequencing/timing as per COP/JTAG connections.

•

Maps/re-maps P5040/P5020 local bus chip selects to FLASH, compact FLASH, and so on.

Содержание P5010














































































Отзывы:

Нет отзывов