NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 51

NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 48

NXP Semiconductors

UM11636

KITPF5200SKTEVM evaluation board

SET_REG:PF5200:M_OTP:OTP_OV_BYPASS1:0x00
SET_REG:PF5200:M_OTP:OTP_UV_BYPASS1:0x00
SET_REG:PF5200:M_OTP:OTP_ILIM_BYPASS1:0x00
SET_REG:PF5200:M_OTP:OTP_PROG_IDH:0x00
SET_REG:PF5200:M_OTP:OTP_PROG_IDL:0x00
SET_REG:PF5200:M_OTP:OTP_DEBUG1:0x00
SET_REG:PF5200:M_OTP:OTP_SW_COMP1:0x00
SET_REG:PF5200:M_OTP:OTP_SW_RAMP:0x00
//SET CRC VALUES
SET_REG:PF5200:OTP_PAGE2:FCMD:0xA5
SET_REG:PF5200:OTP_PAGE2:FCMD:0xA4
SET_DPIN:PF5200:TBBEN:low
SET_DPIN:PF5200:PWRON:high

7 References

[1]

PF5200

— detailed information on PF5200, Dual-Channel PMIC for Automotive Applications – 2 High Efficient

LVBUCK, Fit for ASIL B Safety Level

http://www.nxp.com/PF5200

[2]

KITPF5200SKTEVM

— detailed information on this board, including documentation, downloads, and software and

tools

http://www.nxp.com/KITPF5200SKTEVM

[3]

NXP GUI for Automotive PMIC Families

— Software GUI for NXP's Automotive PMIC products

https://www.nxp.com/PMIC-GUI-SW

UM11636

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 2 — 13 December 2021

48 / 51

«
...
46
47
48
49
50
...
»

Содержание KITPF5200SKTEVM




















































Отзывы:

Нет отзывов