manualshive.com logo in svg

NXP Semiconductors KITPF5200SKTEVM, Руководство пользователя, Страница: 11 / 51

Поделиться
Скачать
NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 11

NXP Semiconductors

UM11636

KITPF5200SKTEVM evaluation board

3. Disconnect and reconnect the USB cable into the SDA port.

•

This time without pressing the RST push-button, the FRDM_KL25Z device should

appear on the left pane of the File explorer as shown in the following figure.

4. Locate the file “

nxp-gui-fw-frdmkl25z-usb_hid-pf5200_v0.9.bin

” from the package

and drag and drop the file into the FRDM_KL25Z device.

•

Note: Make sure to allow enough time for the firmware to be saved.

5. Freedom board firmware is successfully loaded. Disconnect the USB cable from the

SDA port and reconnect it to the FRDM-KL25Z USB port.

5.1.2 Flashing the FRDM-KL25Z firmware – Windows 10

1. Disable the storage services: run the services, double-click on the storage service

from the list and press the Stop button.

 

 

If BOOTLOADER is already loaded on the FRDM-KL25Z board, skip Step 2 and Step

3 and start with Step 4.

2. Press the RST push-button and plug the USB cable into the SDA port on the Freedom

board.

a. A new “BOOTLOADER” device should appear on the left pane of the File explorer.

3. Drag and drop the file “MSD-DEBUG-FRDM-KL25Z_Pemicro_v118.SDA” into the

BOOTLOADER drive.

a. Note: Make sure to allow enough time for the firmware to be saved in the

bootloader.

UM11636

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 2 — 13 December 2021

11 / 51

Содержание KITPF5200SKTEVM




















































Отзывы:

Нет отзывов