NXP Semiconductors KITPF5200FRDMEVM Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 51

NXP Semiconductors KITPF5200FRDMEVM Скачать руководство пользователя страница 38

NXP Semiconductors

UM11723

KITPF5200FRDMEVM evaluation board

The SW regulators tab gives the main setting of each switch and monitoring

configuration.

5.2.3.4.3 Sequence

The Sequence tab sets up the power up/power down sequence and the switcher slot

assignments for the device. The tab has three sections:

•

Power down sequencing: allows you to read or write power down sequencing

parameters.

•

Power up sequencing: allows you to read or write power up sequencing parameters.

•

Switcher slot: allows you to read or write the slots assigned to SW1 and SW2.

5.2.3.4.4 Clock

The Clock tab manages the SYNC pin, switcher clock frequency, and spread spectrum.
The SYNC pin can be used to either output the switcher frequency or to input the

frequency synchronization signal. When SYNCOUT_EN is enabled (SYNC pin is output),

FSYNC_RANGE (the SYNC pin used as the synchronization pin) is not usable and

therefore is not available.

UM11723

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 1 — 8 December 2021

38 / 51

«
...
36
37
38
39
40
...
»

Содержание KITPF5200FRDMEVM




















































Отзывы:

Нет отзывов